Mike’s solution for sticky radios

Many shortwave radios, such as those manufactured by Grundig/Eton, have been produced with a rubberized coating that makes the radio easier to hold in the hand. I like this coating because it gives me a sure grip on the radio.

However, over time (say, two to three years) the coating can break down and begin to produce a sticky residue. All of a sudden your “grippy” coating feels more like tacky paint–even leaving a bit of residue on anything it touches.

Many models have this coating: The Grudig G5 and G3, The Eton E1, E1-XM, FR350, FR400, FR500 and FR600, to name a few.

Michael Kitchen (KD5PXH) recently wrote with his solution for sticky radios:

After experementing with cotton balls/pads, and using window cleaner and other liquid agents, I managed to decently remove the gummy coating from an Eton FR-400.

Best to use 91% Isopropyl Alcohol, and a clean but disposable (dry) wash cloth or something similar.

The stronger percentage alcohol makes for easier breaking down of the sticky, and the wash cloth to remove, without damaging the surface or removing lettering. The trick is to always use clean spot on wash cloth, keep from just smearing the stickyness around. The wash cloth will lift and absorb sticky, so keep using a clean spot on cloth. The cloth needs only be damp with alcohol, not dripping wet. Use dry spot on cloth to wipe clean the surface.

There may be a hazy white patina, but much of this can be wiped away.

It takes a little bit of effort, but the results are worth while.

Thank, Mike!

Spread the radio love

38 thoughts on “Mike’s solution for sticky radios

  1. Dennis

    There are times when, in spite of the destruction it seems to be wreaking on our civilization as a whole, I have to say BY GOD I LOVE THE INTERNET! I put the phrase “eton radio sticky” in my search bar and VOILA! This web page! I’m now a proud owner of a no-longer-sticky Eton Red Cross emergency radio.

    I used Goo-Gone and it worked like a charm. My method: Goo-Gone on an old toothbrush, massage by section, remove with a clean cloth. I put in perhaps twenty to thirty minutes.

    Thanks to all contributors. Life is good again.

    Reply
  2. Chris

    Wow, thank you for this fix!

    I only had 99% alcohol on hand so used it. Just slightly dampened a cloth and gently rubbed a small section then wiped with a dry rag.
    Amazing results and note for the first time in years I am using my Grundig mini 300 every day!

    Thank you!

    Reply
    1. Roy Fowler

      I second this response. Googling the problem and not exoecting to find ANYTHING I found your answer. Haven’t tried it yet but it gives me hope. Degen handheld radio here.

      Reply
  3. Jo Ann

    I have Genesis radio and CD player in my Flagstaff
    Travel Trailer. It has gotten so bad buttons are stuck on and won’t move to turn off. Can someone tell me if I can remove the front cover to clean it and all buttons.

    Reply
  4. Edward

    Hey Mike, man, you were on point. I was so upset that my Grundig G6 Aviator (Buzz Aldrin Ed.) started feeling like fly paper. I did what you suggested and man, it looks brand new. Thanks a bunch.

    Reply
    1. Paul Campbell

      I have an ETON FR 160, not sure of age, but still works great. But it has the same sticky surfaces everyone is talking about. I called Eton Customer Service ( 1-800.872.2228) this morning, she told there is a cleaner called Purple Power Cleaner/De-greaser (price at Dollar General is $3 and it goes up to $14 + for two bottles at Amazon ), she said Walmart carries it and she believes most Auto supply stores do also. She also said to use a clean cloth an ONLY CLEAN in the SAME DIRECTION each time. I have not tried it yet, but will.
      localpeon

      Reply
      1. Imke Sanderson

        Even better than 91% alcohol is strong nail varnish remover. It contains acetone and alcohol. I cut a long 2″ strip from an old towel and used that on my radios, but folding it down after each small area I attacked. It can then be turned to the other side as well.
        I can finally bear to touch the radios again. and the white one has come up especially well.

        Reply
  5. UHF

    Too bad America’s landfills are each day filled with planned obsolescence and a decaying population of fixers. I wanted to salvage the generator, but fingers so sticky even putting in trash. If it’s not built in the 70’s or before, forget it.

    Reply
    1. Thomas Henden

      Agreed! It seems like an irony, that even an emergency – hand cranked radio meant for storage 10-20-30 years (hopefully never needed to be used of course) is made with a type of plastic that in practice makes the radio unusable after 2-3 years. Even though the thread starter thought the grip of the radio was nice, don’t forget that products have been made long ago already, with some types of very durable rubber for good grip, without this stickyness as a result.

      So please boycott such products and also other plastic products that just contributes to the plastic problem on earth, that is the only way there can be some changes on this planet to reduce plastic pollution and the artificial obsolence of even simple radios. Have even seen a lot of very expencive DAB radios in my country with this type of plastic that goes from “soft” to sticky in a few years.

      (Sorry for my english, I am from Norway)

      Reply
  6. Cassandraguy

    I used Krud Kutter and a terry cloth towel with lots of rubbing. Works well. No damage to graphics or lettering. This is a CC Crane Observer about 5-6 years old. We’ll see if it returns.

    Reply
  7. Rick

    Thanks for the tip;
    I used rubbing alcohol compound (ethanol anhydrous 746.5 mg/ml) and followed your instructions.
    Finally have a usable Grundig G8 Traveller II Digital
    Thanks again.

    Reply
  8. Patty

    I saw someone recommend using oven cleaner and a rag. I sprayed no fume oven cleaner on a dry magic eraser and it worked instantly. Used a dry rag to polish it. Just don’t scrub the lettering off. My radio was very sentimental as it belonged to my dad. So glad this worked.

    Reply
  9. peter d

    I used Elmer’s sticky out adhesive remover on my Eton e-100. Like others have said change your rag often otherwise you’ll just smear the sticky residue all over. Radio turned out great in about 30 minutes.

    Reply
  10. Kristine

    I did not have oven cleaner but I had Simple Green all purpose cleaner in a concentrate. So I tried some in a small area to see and it worked amazingly! I have a Grundig mini 300 that I use at ball games so was happy I was able to remove all the stickiness.

    Reply
  11. Ki6H

    Just cleaned my Eton E1 with EZ-Off oven cleaner, dabbed on with a cotton cloth & immediately wiped off, a square inch at a time. Used swabs for tight spots. Looks great! Took about an hour.

    Reply
  12. Leonard Sims

    What about painting over the white sticky surface with clear lacquer or clear epoxy paint, while preserving the black lettering? Any ideas? The quality of the radio tuner is excellent and I would hate to trash it.

    Reply
  13. toni

    Have the same issue with “Mini 300” I used medical alcohol prep pads and sticky came off!

    Not rubber coating but plastic. Anyone think this is from finger prints and acid from those prints?

    Reply
  14. Leslie

    Was ready to discard the radio to the e-heap, but before that final act decided to google the problem, and oh my, so many with the same thing. I could not figure it out, used paint thinner(a respondent just above me had success) well I did not, it spread the gunk all over instead.Also tried nail polish remover to no avail, it became even stickier. Then wanted to buy a new one but I am glad I did not do that, would have been the same problem.

    Reply
  15. Harry

    I hadn’t used my Eton in several years and just discovered that it had this problem. I used paint thinner (not laquer thinner!) applied sparingly to a paper towel and cleaned half in about 5-10 minutes. The next day I did the other half using a paper towel and q-tips for the recessed areas. That was another 10 minutes or so. The haze mentioned above is not evident. I don’t know why it would take hours to do this. Perhaps the coatings are different or maybe mine was so far gone that it came off easily. I would be leery of using a water based cleaner – if it gets inside the radio it could be the end.

    Reply
  16. Andy

    Coatings which eventually become sticky have been applied to many consumer products, so shame on whoever sells it without adequate accelerated life testing. Although it increases grip, it less pleasant than a nice shiny finish in my opinion. I first encountered trouble with binoculars of both miniature and zoom varieties. I found sticky label remover very effective, but it must be used very sparingly to avoid “melting” the plastic underneath and leaving permanent marks. The treatment must be repeated if the stickiness is not all removed in one go. To produce a shiny surface once the coating has been cleaned off, I use metal polish on a cloth. Make a sparing application and buff up vigorously. Repeat as necessary. My binoculars are now pleasant to handle and shiny in appearance. Much better. Because the hard plastic underneath has been exposed, I do not expect the surface to become sticky again. (G4EAQ)

    Reply
  17. tom

    Does anyone know if the manufacturer will help out with this stickiness problem. Usually manufacturers stand by their product.

    Reply
    1. Thomas Post author

      If the radio is within its warranty period, I’m sure Eton will help. Typically, though, the sticky residue surfaces after a few years of use. My G3 hasn’t developed it yet, but a 7 year old FR-350 has.

      Reply
    2. Phil

      Tom I called the company. I spoke to customer support. The guy I spoke to one about the sticky problem and told me to try nail polish remover. He said that may work. Basically he wasn’t much help. But who knows, if you can stand the fumes I guess it could work.

      Reply
  18. michael

    I tried the borax idea – 5 dollar box of borax and dollar dobie sponge and it was clean in 10-15 min.
    Only took that long since i was trying to be careful about over saturating my dobie and getting a lot of water in the fr300 (of course with no batteries in it, but still)
    Not sure why he needed a vacuum cleaner but i just got the dobie damp, put some borax on and cleaned, then wiped with a dry towel right after
    Easy-peasy

    Reply
  19. Ian

    I found a real easy fix.
    Use borax on a moist rag and it wipes off easy.
    Then use a vacuum cleaner to get the borax off the radio.

    Cleaned in 5 minutes.

    Reply
  20. Dan Frechette

    I had one of these I bought off of ebay a few years back that developed this stickiness. I thought it must be defective so I threw it out eventually. I recently found my original Eaton G10 and it had developed the exact same issue, plus it was completely covered in cat hair! So far I’m resisting the temptation to chuck it.

    I used olive oil and paper towels to clean this gunk off. It works great and doesn’t leave a white residue. Oil and a cloth would be better than paper towels though. I use the same method on removing glue left over from labels or things like that.

    I’m not sure if it’s worth keeping this radio if this glue stuff will keep leaching out. Very dumb design for an otherwise great radio.

    Reply
  21. Eric Schleppegrell

    After cleaning good with the 91 rubbing alcohol, give the cabinet a good waxing with a carnauba liquid cleaner /wax. It removes remaining stickiness and the ugly haze left by the alcohol.

    Reply
  22. leah

    Sean, the service is worth your asking price but, sadly, a new Eton radio costs the same or less, money-wise. And that problem exists across the world of appliances, electronics and autos. Ownership ought to be obsolete. Leasing serves better, for a better world. Revenue from leasing leads to: Tons of service jobs created everywhere! products designed and manufactured in anticipation of their ongoing fixability! Landfills left hungry! and other subversions of today’s unhappy status quo.

    Reply
  23. Sean

    Dear Mike and all else,
    After successfully finding a good solution to this issue specifically with the Eton E1 and E1XM, I am now going to put myself on a limb and say that for those not brave enough to tackle the issue on their own E1 radios, I may be able to help them (E1 and E1XM only for now). I have decided to offer this as a service to folks outside my circle of friends now. Because it takes anyplace from 4-5 hours to thoroughly remove the coating from these radios I am looking at charging $100 plus shipping. I know that sounds like a lot for a radio someone already spent a bunch of money on but these are great radios and I have heard from some people that they just find them totally unusable as they continue to get more and more gummy with age. Removing the gummy surface coating is not easy, takes a lot of time and some materials so the cost is actually reasonable for the effort. These radios, when they are not suffering from the dreaded display issues are well worth keeping alive and in play. One issue I wondered about before tackling my first subject radio was, is the lettering on top of or underneath the gummy residue? It’s under and pretty well painted on. Still, with some chemicals there is a chance of them rubbing off so if you do this at home, be cautious of the chemicals you use.

    If anyone is interested in me doing this for them, you can contact me at [email protected]

    Thanks.

    Reply
  24. William Thébonger

    Many thanks indeed.
    My Eton E1 nows looks better than new. About six hours of rubbing, wiping and patience!
    Was spurred on by seeing the original white printing revealing itself. Final polish achieved by using a soft impregnated shoe mitt that are sometimes provided in hotels.
    All the best to all.
    WT

    Reply
  25. Lou Delgado

    Thanks .. I’ll give it a go .. shame the company made the product with this rubberized coating … otherwise I love the radio .. thx for your help … be well — Lou

    Reply
  26. Mike McShan

    I tried this method with my Eton E1, and it worked great! It is so nice to be rid of that sticky stuff that covered the radio; thank you for the tip!

    Reply
    1. Peter Munselle

      I tried rubbing alcohol, ram, paint thinner, laquer thinner, all with poor results. I had my best success with a diluted solution of tsp. (1tbs to a pint of water) I used a toothbrush
      and clean dry rag to remove the residue. It did a reasonable good, but not perfect job.

      You would think that with all of the complaints over the years that the manufacturer would have substituted more more appropriate material. When the first thing that appears in google search for Eton radios is “eton radio sticky” you know something is wrong.

      Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.