Tag Archives: NPOTA

A quick recap of yesterday’s Carl Sandburg Home NPOTA activation

img_20160908_172739245_hdr

Yesterday, I fit in yet another activation of the Carl Sandburg Home (NS01) for the ARRL National Parks on the Air. You might recall, I activated the same site last Sunday.

The lake at the trail head.

The lake at the trail head.

Second time’s a charm!

Since I had already scoped out the site and the trail where I operated last time, I took a minimum of supplies: My Elecraft KX2, EFT Trail-Friendly antenna and the accessories in my go kit:

LowePro CS 60 Closed

I didn’t even need a folding chair as I hiked further into the trail system and found a bench in an ideal shady location where I could hang the EFT antenna without any part of the wire being close to the trail itself.

The only negative was that I had to fight off a few mosquitoes–par for the course!

img_20160908_163154954_hdr

After firing up the KX2, I found that both frequencies I announced (14,286 and 7,286 kHz) were occupied. I tuned around and found clear frequencies then posted the changes on Twitter and the ARRL NPOTA Facebook page. Fortunately, I was spotted on the DX clusters after my first contacts (thanks, Mike and others!).

In short: this was about the busiest I’ve ever been on the radio.

In 43 minutes, I logged 41 stations: many stations here in the southeast US, and stations from New Mexico to Italy! Propagation and timing were certainly in my favor.

The rubber band held my KX2 to the clipboard, but I hope to sort out an even better way of securing it.

This red rubber band held my KX2 to the clipboard, but I hope to sort out an even better way of securing it in the future.

The pileups were heavy enough that I didn’t even have time to properly pull log sheets once I had completed them–instead, I folded them over the KX2 and continued writing.

I was very pleased that I logged at least one SWLing Post reader: Randy (KS4L). Thanks for the contact, Randy!

Not all portable operations go so well…but when they do, it’s energizing!

I might be able to squeeze in a 30 minute activation on the Blue Ridge Parkway (PK01) this afternoon.  Listen for me (K4SWL) around 14,286 kHz SSB sometime between 20:30-21:30 UTC. That is, if propagation and my schedule cooperate again!

Spread the radio love

NPOTA: Activating the Carl Sandburg Home (NS07) today

Elecraft Kx2 ON Clipboard

This afternoon (September 8), I should have a chance to activate the Carl Sandburg Home again for the ARRL National Parks on the Air program. You might recall, I activated the site Sunday as well.

I’ll plan to use the Elecraft KX2 and EFT TRail-Friendly antenna combo once again.

I should be on the air starting sometime between 20:00-20:30 UTC (4:00 – 4:30 PM EDT). I’ll plan to operate SSB on two frequencies: 14286 and 7286 kHz. I should be on the air for one hour or so, if all goes well. Listen for my amateur radio call sign: K4SWL.

It would be fantastic to log some SWLing Post readers. If you do manage to hear my 10 watt signal, or work my station, please comment!

Spread the radio love

Labor Day Fun: A hamfest, an NPOTA activation–and a new Elecraft KX2 QRP kit

NS07-Carl-Sandburg-Home

My station location on the trail near the Sandburg farm is indicated with the small grey marker (lower left quadrant).

I’ve enjoyed an especially “radio-active” Labor Day weekend.  Here’s hoping you did, too.

On Saturday I headed out the door at 4:15 AM to meet my buddy Vlado (N3CZ), the inimitable radio doctor; we aimed our headlights through the morning mist to the Shelby Hamfest. Though it took quite a bit more coffee to keep me going, the hamfest was a load of fun. Check out the photos I posted yesterday.

ARRL-NPOTAOn Sunday, I enjoyed some family time. Conveniently, our weekend travel took us near the Carl Sandburg Home in East Flat Rock, NC.  I managed to carve out a little time for a quick–very quick– NPOTA activation of the site.

I realized I would only have about an hour, though, to find a suitable site, setup my radio kit, make at least the minimum of ten contacts, then pack up and clear out.  Not an optimal amount of time, but certainly a fun challenge.

This was also a good excuse to try out my new Elecraft KX2 portable transceiver kit in the field. I haven’t even had the KX2 for a full week, but I quickly put together a field kit with the Elecraft as a centerpiece.  If you’re curious, the kit consists of the following:

  • The Elecraft KX2, with internal battery and ATU options
  • An LnR Precision EFT Trail-Friendly antenna (purchased at the Dayton Hamvention)
  • An assortment of connectors and adapters
  • A six-foot coax cable
  • An Elecraft hand mic, borrowed from my KX3
  • A CW paddle (the KXPD2)
  • A clipboard, log sheets, and mechanical pencil
  • Fishing line and a weight (to hang the antenna)

All of this, save the fishing line and weight, was protected by the compact and perfectly portable LowePro ViewPoint CS 60 padded case, and fit it like a glove.

LowePro CS 60 Closed

Let’s talk packs…

Those of you who know me, know that I’m a bit of a pack junkie.  So I’m kind of picky about what I choose to hold my gear. There are a few manufacturers whose packs pass the test, and that make gear here in the States, like Spec-Ops Brand, Red Oxx, and Tom Bihn. Their packs are sometimes pricey, but they’re nearly bullet-proof and guaranteed for life.  Timbuk2, based in San Francisco, is a more economical company with good gear, as well.

After purchasing my KX2, I searched but couldn’t find a suitable pack from my prefered manufacturers. I had remembered that at the Dayton Hamvention, Elecraft was actually selling two models of a LowePro pack that fit the KX2 exactly: the ViewPoint CS 40 and CS 60.

While I like to go as compact as possible, the CS 40 is just  a bit too small to hold everything I like to carry to the field (antenna, paddle, and mic). The CS 60, on the other hand, could hold everything and has a fold out panel organizer to hold connectors.

I knew the CS 60 would fit the KX2, and I knew the CS 60 was padded to protect its contents.  I also could see that the pack has excellent (and apparently genuine) ratings on Amazon, so I ordered one.

I’m pleased to report that the CS 60 is very well built indeed, and what’s more, accommodates everything I need. In fact, the only thing the CS 60 won’t hold is my reel of fishing line and 6′ coax cable (and yes, I daresay you could adapt both items to make them fit with a little effort).

I carried the CS 60 and reel in my trusty 20-year-old Dana Design lumbar pack:

Dana-Design-Pack

There was room to spare inside for water bottle and snacks, and the whole package was very lightweight.

The Carl Sandburg Home

Carl-Sandburg-NS07

The Carl Sandburg site was fairly teeming with visitors, also enjoying the warm weather of the Labor Day weekend. After arriving and (fortunately) finding a parking spot, I hiked 20 minutes to one of the trails, where I was given permission to hang an antenna and operate.

Knowing that I needed to rejoin my family soon, I wasn’t too choosy about my site this time. I just needed to get on the air and work the minimum of ten contacts. In truth, I wasn’t sure if all of this was possible in the one hour I had available.

I setup on the right side of this trail, near one of the park benches.

I setup on the right side of this sunlit trail, near one of the park benches. It turned out to be a pretty good spot.

It took me perhaps ten minutes to set up, with a few brief asides to explain what I was doing to passing hikers.

Since I configured my little Elecraft KX2 with an internal battery and antenna tuner, I had no need for extra power cables, connectors, ATU and coax.

Elecraft-KX2-Clipboard-NPOTA

Yep, my entire station easily fit on the clipboard I was using to hold my log sheets. On my lap, the clipboard became my operating table.

As soon as I sat down in my folding chair, I turned on the KX2, set the frequency to 14,286 kHz, and pressed the ATU button which gave me a 1:1 match (since the EFT is resonant).

Thank you, voice keyer!

Next, I recorded my CQ call into the KX2’s built-in voice keyer by:

  1. pressing and holding the MSG button,
  2. assigning the voice message to “memory allocation 1” by pressing the PRE (1) button,
  3. pressing XMIT to start the recording,
  4. reading off my CQ call “CQ, CQ, CQ, this is K4SWL calling CQ for National Parks on the Air…”, and
  5. pressing XMIT again to stop the recording.

Then I started calling CQ by simply pressing the MSG button and selecting my message stored in memory allocation 1 by pressing and holding the PRE (1) button.

By pressing and holding the PRE (1) button, I initiated a loop-playback of my CQ call where my KX2 would transmit my call from memory.  Then I waited a few seconds to listen for any replies, and played it again. (In loop-playback mode, the KX2 will repeat my CQ call until I interrupt it by pressing a button or keying my mic.)

It’s a brilliant and easy function which saves my voice! By automatically calling CQ, it  gives me an opportunity to answer questions from curious passersby,  naturally fascinated by a guy sitting on the side of a trail, talking into a little box connected to a tree-branch suspended wire.

In the end, I didn’t even need to use the voice keyer that much. I was spotted on the DX cluster and within moments had a small pile-up of stations. Remarkably, I worked my minimum of ten stations within six minutes! Of course, I continued to call CQ until I worked everyone in the pile-up (including stations from California, Nebraska, Kansas, Texas and Mexico). Though I was running out of time quickly, I did switch to the less-active 40 meter band and called CQ. In a period of a few minutes, I worked two stations on forty: one from Alabama and one from Florida. Not bad for 10 watts of power!

Elecraft Kx2 ON Clipboard

Packing up

Normally I would have stayed on the air for at least an hour to give chasers an opportunity to work my station, but I was pleased that I’d managed to fit this activation into a very busy schedule. I was glad to have racked up so many stations, so quickly!

Taking down the antenna and packing up my portable station took all of eight minutes.

Without a doubt–once I had hiked to my operating site–this was my fastest deployment, activation, and pack-up to date. It was all possible because:

  1. the KX2 has a built-in battery pack and ATU, and is so small it fits on my clipboard,
  2. the EFT Trail-Friendly antenna is a breeze to install, take down and pack, and
  3. the CS 60 pack organizes the radio and accessories so handily.

LowePro-CS-60-Open

In short: I’m totally pumped by my new QRP field kit!

More radio adventures await…To the field!

Spread the radio love

NPOTA activation on the Blue Ridge Parkway

A crowd gathers as Vlado (N3CZ) works station after station in CW!

A crowd gathers as Vlado (N3CZ) works station after station in CW!

I’m not sure what I’m going to do after the National Parks On The Air event is over at the end of this year. I hope the ARRL organizes something equally as fun for 2017.

Truth is, I love playing radio outdoors and I love National Parks. The two are a perfect combo.

Vlado (N3CZ) on left, and me (K4SWL) on right.

Vlado (N3CZ) on left, and me (K4SWL) on right.

My buddy, Vlado (N3CZ), and I decided to do an NPOTA activation on Sunday. The weather was fantastic–a little foggy with mild temperatures and the HF bands were open!

We arrived at our site–the Craggy Gardens Picnic Area (PK01)–at 14:30 UTC or so.

KX3-PK01-NPOTA

We brought the following antennas and supports:

  • a self-contained  20 meter band telescopic fiberglass vertical (I recently purchased at the WCARS Hamfest for $40–!) and
  • a 31 foot fiberglass Jackite pole (the fluorescent orange on in the photos) which we used to suspend a homemade 40 meter doublet Vlado built the day before.

Setup was quick. We were both especially pleased the 20 meter vertical. It was so easy to install, even considering it was the first time either of us had used it.

I powered the LD-11 and the KX3 with my QRP Ranger.

The 20 meter vertical antenna.

The 20 meter vertical antenna (in foreground).

I operated SSB from a picnic table using the LnR Precision LD-11 transceiver, connected to the doublet on 40 meters, and the mono-band vertical on 20 meters.

LD-11-QRP-Ranger-NPOTA-PK01

Vlado started by operating CW with his Icom IC-7000 which was installed in his car, but later moved to the picnic table and logged a number of contacts with the Elecraft KX3.

N3CZ--NPOTA-PK01

We easily logged the number of stations needed to activate the site.

The 40 meter band was hopping and a good path was open into Ohio, Virginia and other surrounding states. The 20 meter band was serving up some excellent QRP DX.

Vlado-KX3

Vlado operating CW on the 40 meter band.

When I moved to the 20 meter band, the noise floor was so low on the LD-11, I thought perhaps the band was dead.  Not so!

LD-11-NPOTA-PK01

It’s hard to believe that with a mere eight watts in SSB  I worked Rhode Island, Texas, Montana, Manitoba, Washington, California and Slovenia from a picnic table on the Blue Ridge Parkway.

Reports on the LD-11 audio were all very positive. I’ve used the LD-11 for eight NPOTA activations this year and can say with confidence that it’s a brilliant & fun little field radio. (FYI: I’ll be publishing a full review of the LD-11 in the October 2016 issue of The Spectrum Monitor magazine.)

Vlado and I are planning on several more activations together this year. Our next one will most likely be at the Carl Sandburg Home-. I can’t wait!

Any other post readers participating as an activator or chaser in the National Parks on the Air event?

Spread the radio love

National Parks On The Air: Activating PK01 this weekend (August 28)

The QRP Ranger (left) and LNR Precision LD-11 transceiver (right)

The QRP Ranger (left) and LNR Precision LD-11 transceiver (right)

After two months in Canada and one month spent catching up on work, I’m pleased to make some time this weekend to activate PK01 (the Blue Ridge Parkway) for the ARRL National Parks On The Air (NPOTA).

I’ll be joined by my good friend, Vlado (N3CZ) on August 28–we plan to set up at the Folk Art Center on the parkway around 11:00 EDT and be on the air by 11:30 EDT (15:30 UTC).

I plan to use the LNR Precision LD-11, QRP Ranger and EFT Trail Friendly Antenna combo. Vlado will either use his Icom IC-7000, Kenwood TS-480 or my Elecraft KX1.

Look for us on the following frequencies:

  • CW: +/- 7031, 14061 kHz
  • SSB: +/- 7286, 14286 kHz

Life has been so hectic after having been on the road for two months–I’m pleased to finally have a moment to play radio in the field again!

Spread the radio love

Back at the dial again…!

Ship-Throttle

Many of you might have noticed I’ve been absent on Facebook/Twitter , slower to correspond, and not posting quite as often this summer.

Yes, you guessed it: I’ve been on the road again.

Starting in mid-May, we made our annual pilgrimage to Dayton, Ohio, where we hosted an inside exhibit at the Hamvention, made some NPOTA activations, and visited the phenomenal National Museum of the USAF.

The LNR Precision LD-11 and QRP Ranger during a National Parks On The Air (NPOTA) activation in Ohio.

The LNR Precision LD-11 and QRP Ranger during a National Parks On The Air (NPOTA) activation in Ohio.

I then returned to the shack for one week, frantically finished a few projects, then hit the road again.  Headed even farther north this time….Destination: Canada.

The Udvar-Hazy Center houses a number of large aircraft including the Concorde, the SR-71 and even the space shuttle Discovery.

The Smithsonian’s Udvar-Hazy Center houses a number of large aircraft including the Concorde, the SR-71 and even the space shuttle Discovery.

Stopped in the Washington, DC area for a few nights and spent the better part of one day at the Udvar-Hazy Center. The aviation geek in me was in the skies––wow, what an amazing place!

By June 5th, i was just outside Québec City in the town of Beaupré.

My station on Field Day operating as VE2CQ.

My station on Field Day operating as VE2CQ.

While in Québec, I participated in a Field Day event with the incroyable members of the Club Radio Amateur de Québec. I practiced my French, the club members treated me like one of their own––hosting an excellent lunch and dinner––and I even got a few hours on the air as VE2CQ.

Oh, and you might recall a post from June in which I shared photos from an aerial display in Québec City featuring the Snowbirds. It was our first time seeing them, and it was, as you might expect, just spectacular.

DSC_5113

We spent the rest of June and part of July in Québec, then made our way to Prince Edward Island via New Brunswick and Nova Scotia where a rustic off-grid cabin awaited us.

The view from our off-grid cabin on PEI.

The view from our off-grid cabin on PEI.

While the condo in Quebec had all of the radio interference one would expect, the off-grid cabin was blissfully quiet, free of radio interference. As you might imagine, I played a lot of radio…

7BDA6D19-2FC6-4D6D-8C3C-B34E9EF8ADE3

I also sampled a lot of Island craft brews!

We spent several relaxed weeks in Prince Edward Island, then made our way back to the States.

I’ve only been home since last Wednesday, and found quite a pile-up in the work zone, so I’m busily catching up.  However, I’m finally starting to see the light at the end of the tunnel and I should be current with correspondence by next week.  Thanks for your patience, email friends!

And if you’re interested, just for fun, I plan to write a more detailed trip report later this summer or fall. I do have a few pics from side trips I’ll likely share in the meantime.

Yet again, we had a terrific adventure in Canada!  But it’s sure good to be back home…and back at the dial.

Anyone else done a bit of traveling this season? Feel free to share & comment!

Spread the radio love

One week of Hamvention, Air Force Museum, Wright Brothers and National Parks On The Air

DSC_4449I returned home last night from my week-log Dayton Hamvention trip around 8:30 PM.

The Hamvention actually ended at 1:00 PM on Sunday, May 22, but my buddy Eric McFadden (WD8RIF), his son Miles (KD8KNC) and I stayed Sunday night in Dayton, and Monday night at Eric’s home in Athens, Ohio.

After packing up our Hamvention booth (for Ears To Our World) on Sunday, we made our way to the nearby National Museum of the USAF–the largest aviation museum in the world. We visit the museum every year–and every year I discover something new.

BC-348-B29

This BC-348 can be found in one of the museum’s B-29 displays.

DSC_4443 DSC_4455

In June, the Air Force museum is actually opening a fourth building which will house an additional 70 aircraft in four new galleries.

If you’re an aviation buff–trust me–the  National Museum of the USAF is worth a pilgrimage to Dayton, Ohio.

NPOTA activations

Monday morning, Eric, Miles and I packed up, ran a few errands on Wright Patterson Air Force Base, then made our way to our first National Parks On The Air activation: the Dayton Aviation Heritage National Historical Park (HP11) and North Country National Scenic Trail (TR04) “two-fer” at Huffman Prairie Flying Field Interpretive Center in Dayton, Ohio.

Eric worked CW on 20 meters and I worked SSB on 40 meters using the LNR Precision LD-11 transceiver (which I’m currently reviewing) and my recently-purchased Hardened Power Systems QRP Ranger.

For all of my Monday NPOTA activations, I used the EFT Trail Friendly antenna I purchased at the Hamvention:

EFT-Trail-Friendly-Antenna-QRP

The EFT Trail Friendly Antenna made set-up a breeze: simply throw a line into a tree, hang the end of the antenna, then hook up the other end to the feedline/transceiver. No antenna tuner is needed for 40, 20 or 10 meters once the antenna is tuned for resonance. It packs up into a small bundle that easily fits in my radio go-kit (see photo above).

The LD-11/QRP Ranger/EFT antenna combo worked amazingly well and made for very quick deployment.

LNR-LD-11 and QRP Ranger NPOTA

I can easily fit the LD-11 transceiver and QRP Ranger on a foldable metal chair (my make-shift field table!).

My buddy Eric, I should mention, is typically on the leaderboard for NPOTA as he’s an avid QRP field operator.

WD8RIF-20M-Vertical-NPOTA

Eric (WD8RIF) operating NPOTA with his field-portable vertical HF antenna.

You can follow Eric’s activations on QRZ.com or his website.

Eric's field-portable HF vertical packs up into this small canvas bag.

Eric’s field-portable HF vertical packs up into this small canvas bag.

We had a tight NPOTA activation schedule to meet Monday, but after packing up from our first sites, we took 30 minutes to stop by the Wright-Dunbar Interpretive Center and The Wright Cycle Co. museum in downtown Dayton.

IMG_20160523_135344026

Well worth the short visit! Next year, I’ll plan to revisit both museums when I have more time.

Next, we made our way to the second scheduled NPOTA activation site: the Charles Young Buffalo Soldiers National Monument (MN18).

NPOTA-QRP-LD-11-QRP-Ranger

Despite not having my antenna very far off the ground (my antenna line fell down one branch in the process of hanging) I still managed to work a pile-up of stations from Georgia, North Carolina, Ohio, Illinois, Connecticut, Michigan and Indiana. After Eric and I racked up a number of QSOs, we packed up our site in haste and made our way to the final activation of the day: the Hopewell Culture National Historical Park (HP15). We arrived as the Park Ranger was getting in his car to leave for the day!

At Hopewell, I managed to deploy the EFT antenna much higher off the ground. I worked a small pile up of stations from all over the region which, to my surprise, included two radio friends (Ed and Eileen) in Franklin, NC. Eric also worked blogging buddy John Harper, AE5X on 20 meters CW (got your message, John!).

NPOTA-QRP-LD-11-QRP-Ranger-Hopewell

All in all, it was a fantastic day to be outdoors and on the air.

Of course, a side benefit of doing National Parks On The Air activations is that you get to check out all of these amazing park sites.

Without a doubt, this was one fun-filled and radio-centric Hamvention week! It couldn’t have been better.

NPOTA Log

Part of my log sheet for NPOTA HP11 and TRO4 “Two-Fer” activations. Not bad for such a tight schedule!

Thank you

Many thanks to my friends Eric (WD8RIF), Miles (KD8KNC), Mike (K8RAT) and Christine (KM4PDS) for volunteering to manage our Hamvention booth for Ears To Our World. It was a record year for collecting donations. Many thanks to all of you for the support!

I’d also like to thank the SWLing Post readers who stopped by to visit our new location in the Silver Arena–it was great seeing everyone!

Now that I’m back home, I essentially have one week of emails and comments in my backlog to sort before hitting the road again rather soon. I appreciate your patience as I catch up. If you don’t hear back from me soon, it’s okay to give me a nudge! 🙂

Spread the radio love