Repairing the Tecsun PL-600 after electrostatic discharge (ESD)

SWLing Post reader, Michael Taniwha (NZ1MT), has kindly documented how he repaired his Tecsun PL-600 after it went silent on the shortwave bands. If this has happens to you, don’t toss your PL-600, use Mike’s excellent guide below for an inexpensive repair.
(Click on images to enlarge)


TECSUN PL-600 – Electrostatic Discharge Repair
Tecsun-PL600

My TECSUN PL-600 had been a trusty bedside radio companion for the last two years. The radio is also my alarm clock and I use the timers to wake me up each morning to my local AM station WHYN or Radio Australia on SW.

On November 29, 2013 I turned the TECSUN PL-600 on and attempted to tune into some SW stations and was surprised to find the radio stone deaf on all the SW bands….similar to the Steely Dan song FM (No Static At All) except in this case it was SW (No Static At All). Immediately my first thought was that the radio had probably suffered an Electrostatic Discharge (ESD) when I had touched the external antenna while moving it around earlier in the day. I reset the radio and tested all the bands, AM and FM bands seemed to be working OK, yet SW remained dead.

My next step was to open up the radio and look for the obvious.

IMGP0092

Upon opening the radio I was surprised to see two back-to-back IN4148 diodes (D17 & D18) fitted across the external antenna input to ground and that the diode D17 was cracked in half. The back-to-back diodes offer a very high resistance at the micro-volt RF level, but will conduct once the forward voltage (Vf) raises above 1.0V. So for the cost of a few pennies we have a relatively cheap and dirty ESD protection circuit.

IMGP0095

My first thought on the cause of the cracked diode was a manufacturing defect when the diode was soldered in at the factory (in fact I later discovered it was likely broken during assembly of the rear cover at the factory – read on). My next thought was just my luck that the broken diode was probably in the polarity direction that I needed the ESD protection.

The next step was to locate a schematic diagram and start circuit tracing to find the likely blown front-end RF pre-amplifier FET/MOSFET that had been damaged. As luck would have it a schematic of sorts is posted in the TECSUN PL-660/PL-600 Yahoo Groups. See the following Link.
http://groups.yahoo.com/neo/groups/TecsunPL660TecsunPL600/files/PL%20600%20Schematics/

The only issue is the text is mostly in Chinese! However, the parts on the radio PC board are clearly labeled as are the parts on the schematic.

IMGP0109 schem

What I quickly notice is that the schematic shows no ESD protection on the front end (upper highlighted circle), but in fact the radio has additional parts D17and D18 (the back-to-back diodes), and C57 on the PC board coming from the external antenna jack. Whenever the external antenna jack is used the jack disconnects the radios telescopic antenna which is connected to C68 to the antenna jack switch circuit. After this antenna switch the schematic from C126 onwards is correct. Following the schematic we see that both the telescopic antenna and the external antenna go through the DX/NORM/LOCAL antenna switch to the IQ3 (AGC?) transistor and then to the RF pre-amp 2Q1 FET (lower highlighted circle). My educated guess was that the 2Q1 FET type 2SK2394 was damaged by the ESD. Yes the 2Q1 it is a very small SMD type FET.

IMGP0097

My reasoning for the 2Q1 having failed is that FM reception was not affected as the antenna circuit goes directly to the TA75358AP FM decoder chip IC1.

SchematicPL-600

Similarly, AM reception was not affected as the AM signal is primarily from the ferret bar AM ANT coil that uses the 1Q1 FET for RF pre-amplification.

PL-600 Scem2

At this stage I contacted Kaito Electronics Inc. the official US based distributor of TECSUN radios and inquired if they provide component level repairs or provide replacement SMD components. The answer was no to both questions.

I then started hunting around online to locate a replacement 2SK2394 FET which is a Sanyo manufactured FET and finally found one for sale on eBay from hkutsource (Hong Kong UT Source) for $2 + $4 shipping. See following eBay link.

http://www.ebay.com/itm/2SK2394-7-Manu-SANYO-Encapsulation-SOT-23-High-Speed-High-Current-Switching-/130835554230?ssPageName=ADME:L:OU:US:1120

This FET is listed as a 2SK2394-7 but all the specifications line up against the specifications for a 2SK2394. I ordered it on December 6th and it arrived 10 days later enclosed in an ESD bag and packaged in a sturdy little box.

IMGP0116

IMGP0117

IMGP0118

Now the fun starts. To replace the 2Q1 SMD FET I used my needle nosed 40W soldering iron, vacuum pump solder remover and wore my ESD strap to stay grounded. First step was to remove the existing 2Q1 FET.

IMGP0119

Next step was to install the replacement 2Q1, if you haven’t worked with SMD devices before let’s just say it is like working with a live insect, they are small and seem to move around on their own accord.

After much tooth pick (my hi-tech SMD tool) maneuvering I finally had it installed. OK I admit it is a little skewed. Have you noticed I have also installed a replacement D17 diode at the top right of the picture?

IMGP0122

The moment of truth! At this stage I did a quick radio check and fired up the PL-600 on the SW band and tuned into CHU, the Canadian Time Station on 3330 kHz, and picked up a time pip signal. In addition I was tuning into other SW stations and had plenty of static as well.

I now decided to install additional ESD protection on the telescopic antenna input as well using two IN4148 back-to-back diodes. After a quick hunt around in my junk box I located an old PC board with a few IN4148 diodes attached. Quickly removed and tested them using my multimeter diode checker.

IMGP0112

IMGP0111

I then installed the additional ESD diodes as shown below (the ATN label on the PC board is where the antenna wire from the telescopic antenna on the back over is attached).

IMGP0124

Finally it was time to reassemble the radio. This is when I started having real problems as the rear cover just would not reattach. When I looked closely I could see that the plastic support screw hole on the rear cover for the telescopic antenna sits partially against the PC board where the D17 diode is located. Now that explains why that diode was cracked when I first opened up the radio at the beginning of this repair. It appears the two ESD diodes were probably a design afterthought and the rear case wasn’t adjusted to accommodate their location on the PC board.

IMGP0125

To get around this issue I removed the replacement D17 and relocated it to the lower part of the PC board below C57. Once I had moved D17 I could now reassemble the radio and again tested the radio. My TECSUN PL-600 is now back to its trusty role beside my bed and picking up SW stations.

Mike-Tecsun-PL-600-Repaired

In summary if you have a TECSUN PL-600 or PL-660 that is deaf on the SW band it is likely to be an ESD damaged 2Q1 RF pre-amplifier 2SK2394 FET. For $6 and some time and effort you can replace the FET and have your radio back up and running like new.

Michael Taniwha – NZ1MT
Email: To send Michael an email, simply insert his callsign @YMAIL.COM
December 17, 2013


Many thanks, Mike, for the excellent documentation and detailed photos! 

Note that you can also download Mike’s guide as a PDF on the Tecsun PL-660/600 Yahoo Group (membership required).

Spread the radio love

13 thoughts on “Repairing the Tecsun PL-600 after electrostatic discharge (ESD)

  1. John

    Just a question for anyone who has encountered this. There does not seem to be a schematic for the PL660 so I am going on instinct. I have a dead dead receiver and read where someone has changed the voltage regulator. Try as I can, I can’t find a regulator on the boards. If anyone has , please post here directions to find it. Thanks

    Reply
  2. Adrian Van Dongen

    Always liked this site. See You have disassembled the Tecsun pl600. I have a dead #7 entry key. Can You please describe the procedure to separate the case so I can investigate and try to fix the key. Have You ever came across this problem with an entry key?
    Thank You.

    Reply
  3. Dean

    I’ve got a 660 and deaf on all channels was a brilliant radio then just stoped sound went deaf, shame is still picks up on all frequencys but just can’t hear anything I’ve tried headphones the lot still no luck someone suggested earphone as a switch inside so keep unplugging headphones in and out still no joy can anyone help please

    Reply
  4. Emily Taylor

    For no money at all I can have it fully replaced with a new one thanks to the kaito warranty and extra warranty on amazon.

    Reply
  5. Leraughn

    Very interesting . Thank you very much for taking the time to do such a write up. Just a question. Did your external antenna ever work seeing you found the two back-to-back IN4148 diodes were broken? I’ve just bought myself a pl-600 and I’ve found that when I plug in any external antenna the signal disappears altogether and I wonder whether it might be the same issue Of broken diodes. Or should I look elsewhere seeing that I can’t send it back due to the costs involved.

    Reply
  6. James Patterson

    No problems at all like that of the 600.I own the 660 model and checked the board and the back of the board faces the telescopic antenna terminals etc.There are no components faceing to the back.No diodes or anything at all.So the 660 looks to have a completly different board.I like my 660,after testing about 4 off TradeMe that were all faulty on SSB and also had a loud harmonic sound that would climb up and down the frequencies.I acturly checked one 600 off the same seller and it was faulty too.So when buying these Tecsuns it pays to give them a good test first.If you know your way arround portable gen coverage receivers,its quite easy to check them out.

    Reply
  7. Ivica

    Very detailed description. I have same problem and found diode D2 broken R=oo Ohm. After change it i found the switch K1 is broken too (too many switchings up/down). If anybody have information about found replacing part for this switch, please to inform me.
    Thank you for this description and please help about replacing K1.
    Ivica

    Reply
  8. Ronnie

    James I am about to retire taking up SWL again after starting in my teens. I have many experiences and I can suggest you have a few choices. 1. Put up with it (not entirely impractical) but try to minimise the effects with the use of an antenna tuner, batteries only, reduce the RF gain, etc. 2. Buy another 660 – I have two now and the latest 2014 looks like they have modified the circuit around Q39 Q40 and I hope an improvement! 4. Buy an 880 and see if better (I am holding off for the more mature model) 4. Buy a better model second hand receiver. This is tricky I admit, but do your homework for the best rated receivers and then try to find one in good condition. For example, can you pick up an NRD 535 or Drake R8 or similar – they are very good.

    I am finding several of these receivers I now have do exhibit their strengths in different areas and situations and I absolutely urge you to put up several wires for antennas and also several wires for the earth lead – obviously one down to earth but also a short one at an angle to the antenna etc. Use alligator clips to switch in and out and experiment all the combinations. I am astounded the effect the antenna and “earth” combinations can have – so just experiment and find out for yourself.

    Reply
  9. james patterson

    Very well written report on the broken diode problem.Something all PL600 & PL660 owners need to be aware of.All receivers have their faults,some major some small.But no one seems to have added to my messages about the very anoying internaly generated harmonics that are on all HF bands and seem to climb up and down the frequencies,or if anyone has been able to fix or modify this problem.I acturly bought the PL660 and was very proud to own it after reading all the positive reports on it.But as soon as I noticed the generated harmonic coming from inside the receiver and on all HF bands that I listen to,drowning out completely what I was listening to,I soon became very dismayed.Im a dedicated SSB DXer listening mainly to utility stations.So with the receiver switched to SSB,the harmonic seemed to be amplified even more so.Ive read that there are good PL660s and bad ones,infact a very good freind of mine has owned his PL660 for a long while,and states his has never given any of the problems mine did.So are there any more out there that suffer with this problem and are they able to be fixed? This is not a squalsh or mutting problem,this is solely an internal generated harmonic problem,that when you put another AM radio next to it,it also picks it up.So I had to return the receiver feeling very disapointed.Very hard to buy or find good General coverage portable receivers here in NewZealand.Short wave listening seems to be a dieing thing now with computers takeing over peoples lives etc.But there are still us dedicated lot who would find pure delight by sitting in front of your receiver and picking up the most distant station amongst all the hash out there!
    So Im most interested in any improvements that can be made by a general Ham radio operator to fix the harmonic problem,as I would like to buy this receiver again.The receiver has so many positive features and positive reports.Maybe mine came from a bad batch? Anyway hopefully someone knows what can be done.I certainly look forward to any responses.

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.