Wellbrook power supply source?

Wellbrook Mag Loop antenna at Mark Fahey’s QTH near Sydney, Australia.

Many thanks to SWLing Post contributor, David Goren, who writes:

I need a new power supply for one of my Wellbrook loop antennas.

Do you know of good source for reliable ones? I forgot where I obtained the last replacement which worked fine until the wire attaching to the plug worked loose.

Here are the specs:

Plug in Class 2 Transformer
Model: DC1200300R
Input: 120VAC 60 Hz 9W
Output: 12V DC 300mA
manufacturer: Sandin Ltd.

Searching online delivers a mixed bag of somebody’s old power supply.

Post Readers: Any suggestions for David? I’m sure he’s particularly interested in a good quality power supply–one that’s quiet and would last a few years. Please comment and include links when possible!

Spread the radio love

11 thoughts on “Wellbrook power supply source?

  1. TomL

    I use a used Astron RS-4A, which is overkill but the only thing i could find that was not noisy. If you can find a genuine Sangean AC adapter used for the HDR-18 model, that would be cheaper and almost as good.

    Reply
  2. Carlos

    Condor makes excellent linear power supplies. I have a 12v 3.4 A Condor PS that feeds a Wellbrook ALA100M antenna interface, a MFJ 1026 noise canceller and a Winradio G33DDC.
    Why do not you build one yourself? Quite easy, some diodes a couple of capacitors and if you want a cheap LM7812 voltaje regulator. There are plenty of schemes on the web.
    Here is a website that sells interesting linear adapters:
    https://www.poweradapter.co/adapters-linear-ac-adapters-c-78_101.html?zenid=uegocq95euecc0ti8pav7hdr81

    Reply
  3. Chris

    Andrew (from Wellbrook) recommends a specific Jameco power supply (I’ll try to find the link). He stated that certain import/export regulations (in Europe and the States) require him to use the power supply included with all orders. He would like to use a better power supply but is only following regulations. I use a Talentcell 8300mAh lithium ion power pack (~$30.00) to supply my Wellbrook LNP and Eton E1XM. At a modest volume, I can generally get 14-15 hours on a charge. Removing all AC power has reduced noise immensely. Plus, I can go mobile in a few minutes for a dxpedition.

    Reply
  4. Colin Snow

    My Wellbrook supplied adapter failed miserably after a year. It would actually transmit the interference through the antenna broadcasting it for a block in all directions. I replaced It with a JAMECO RELIAPRO AC to DC Power Supply Wall Adapter Transformer Single Output 12 Volt 1 Amp 12 Watt. I’ve never had problem since.

    Reply
    1. Robert Richmond

      ^This, even if a Pyramid or similar affordable brand. Unless going off-grid with batteries, a linear and regulated power supply is the way to go for preamps IMO.

      A dedicated linear regulated power supply is a good investment when factored against its likely many years of viable service.

      I have an older Pyramid version similar to Ron’s Wally World link. Other than once blowing a regulator, which was a quick fix, it has provided like 20+ years of good service so far.

      Reply
  5. Paul Evans

    Just cut the wire where it feels like it broke (flex backwards and forwards to feel where it is – it probably failed right up against the strain relief). Check the polarity on the PSU label (normally +ve to center). Strip back and fit a new coaxial ‘barrel’ DC connector. If it must be waterproof, fill the gaps between the wires and the screw-on barrel after soldering. You can use Ace Hardware part number 12589 (https://www.acehardware.com/departments/paint-and-supplies/caulk-and-sealants/caulk/12589) if in the USA – this goes on white and dries clear so that you can see where it went.

    Reply
  6. rtc

    How about a small sealed gellcell battery used in security systems in homes?
    They are 12v and can easily be recharged.
    Lowes’ sells them.

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.