Dan’s initial review of the Belka-DSP portable shortwave radio

Many thanks to SWLing Post contributor, Dan Robinson, who shares the following guest post:


An Initial Review of the Belka-DSP Shortwave Receiver

by Dan Robinson

A few weeks ago, during daily online excursions, I ran across the Belka-DSP receiver.   This is not really a new receiver. Demonstrations have appeared on You Tube going back into 2019.

The Belka has a price of only about $120 U.S. I felt this was a fairly easy purchase, so I went to the website of Alex Buevky (EU1ME).

The receiver has a tuning range of 1.5 – 30 MHz – note that this is a revision from the description on the Belrig site, which still had a range starting at 3.5 mhz as of the time I am writing this.

The Belka is contained in a small heavy duty metal box – the size reminds one of a few boxes of matches put together – 85x50x20 mm with weight of about 100 grams.  Indeed, the diminutive size is quite striking.

 

Viewing videos of the Belka, including several by Fernando Duarte who runs the FENU site, the immediate impression of the receiver is that it has really decent sensitivity and that it is quiet.

While the menu system appears to be a bit confusing, once you start using the receiver you get used to the logic of it.   From the description of the SDR:

“It is possible to adjust the frequency band both from above, from 2.4 to 4.7 kHz, and from below from 50 to 300 Hz.  In telegraph mode, the frequency band is constant, about 300 Hz, and its center is regulated from 500 Hz to 1 kHz.

The settings of the favorite radio stations can be stored in any of 32 memory locations.

The receiver does not have a built-in speaker, but there is a rather powerful VLF bridge that provides sufficient volume when working with an external speaker, speaker or headphones.

The built-in LI-Ion battery lasts for 24 hours of total operating time on the headphones.

In addition to the built-in battery, the receiver can also work from an external DC voltage source of 5 V.”

The Belrig site is English and Russian, which makes ordering easier.  However, be aware that when you hit purchase using a major credit card you may receive a security alert from the card company.   Once I confirmed, the process completed and I received a verification email from Belrig – quite quickly and efficient.

Communications with Alex has been excellent – he is very responsive to suggestions and input.

The SDR arrived in an excellent small heavy cardboard box wrapped with the typical packing tape for the Belarus postal system.  The receiver itself and a telescopic antenna with BNC connector were wrapped in bubble wrap. No paper instructions – those are available directly at the Belrig site [click here to download PDF manual].

The only other item on the Belrig site is a Panoramic Adapter:

“designed for use as part of a radio receiving path of a transceiver/receiver jointly with a personal computer (PC) and SDR software” according to Belrig.  This Pan@SDR “allows you to visually see the RF spectrum in a band up to 200 kHz as well as to receive and decode different modulation types (depending on a software type). . . [and] may be used without a transceiver as SDR-receiver with fixed oscillator (similarly to SoftRock RX), for example, to listen to amateur and broadcasting stations, to decode and to record telegraph stations with CW skimmer, to control signal quality, to calibrate frequency. It may be used as well as a selective millivoltmeter.”

An unboxing video of the Belrig SDR can be seen here:

Initial impressions

My house in Maryland is notorious for high noise levels – located on a corner, we are surrounded by electric wires on four sides.   My attempts to overcome this with my many main premium receivers involve W6LVP, Wellbrook loops and one PAR-FED long wire located outside, with ANC-4 and other noise reduction efforts in my basement radio shack inside.

When I use various portable receivers upstairs in the den of my home, I usually have to keep them well away from incoming Xfinity/Verizon cable TV and Internet lines.

Usually, I am unable to hear much using portables such as SONY SW-55s and Panasonic RF-B65s while sitting on the sofa in the middle of this large family room due to noise from all of these cable lines.

However, interestingly – using the Belka-DSP receiver I was able to get decent reception at this spot.   I attribute this to the metal construction of the receiver, compared to portables with plastic cases.

Certain portables, notably the CountyComm/Tecsun GP5/PL-360-365 are extremely sensitive to being handled, with substantial signal loss once your hand is removed from the cabinet.  The Belka-DSP exhibits sensitivity to touch, but not as much signal loss as there is when you take your hands off a Tecsun PL-365.

I did notice a few frequencies on the Belka where there are digital artifacts – one occurs at or around 11,810 kHz, the BBC frequency.   You can see that in the accompanying video as I tuned up from 11,810.

Others are noticed at various points all the way up through the receiver’s top tuning range of 30 MHz, though thankfully most are not in major SWL bands.

Digital audio artifacts are seen on portable receivers using IC chips, notably the XHDATA D-808 which has several annoying digi-burps on some key frequencies occupied by stations.   On my D-808 for example, 9,650 kHz has a digital artifact that interferes with reception of Guinea.

Tuning on the Belka is simple once you get used to the steps.  The knob on the right serves for tuning, selection of tuning steps, volume, high-low sensitivity, the various audio “cut-off” modes which essentially function as DSP selectivity.   There are 32 memories. Modes are: LSB, USB, CW, NFM, AM1, AM2. For AM mode, AM1 is the most useful, as AM2 seems to be quite harsh in its various DSP audio modes.

The Belka is very sensitive to the type of speaker it is plugged into, assuming you are not using a bluetooth dongle.  Connecting via a 3.5 mm cable to a basic Brookstone speaker that has bluetooth produced audio overloads on the Belka, requiring careful placement of the speaker in proximity to the radio.

Whether this had anything to do with the quality of 3.5 mm cable I was using, I am not sure.  These audio overload issues were not present using the DSP only with a pair of quality SONY studio headphones.  I have not tested the Belka yet with a bluetooth dongle. So be prepared to do some experimenting with speakers and cables.

As mentioned by one person on SWLing Post, the surprise when I received the Belka was that the tuning range is actually 1.5 to 30 MHz rather than 3.5 MHz shown on the Belrig description and in the video there.

This certainly makes the small Belka more attractive, though one wonders why it could not include the full medium wave band.

Also unclear is whether the Belka will have the capability in future for firmware updates, and addition of any new features such as bluetooth though I have to think that adding bluetooth would impact battery duration.

I posed four questions to Alex, including why he made the decision to have the battery soldered in rather than easily user replaceable with battery terminals, whether he is considering adding bluetooth capability, adding capability for firmware updates, and whether he is thinking about extending coverage to include the full medium wave band.

Alex thanked me for my “interesting questions” adding:

“Now  Belka-DSP  is a final  product in this  regard no updates or modifications are planned in the near future.  We do think about the way how to improve this receiver, how to make it even  more user friendly, but I can not say exactly which changes will take place and when.  Looking forward for your future questions.”

Alex says that the Belka receivers ship out with batteries not fully charged to comply with post office regulations.

For me, the battery issue is a bit annoying.  Similar to cellphones with built-in batteries this means that when the Li-Ion cell does deteriorate you are stuck with a bit of soldering to replace it – and I am not good at soldering.

Another example of this practice is the Pocket SDR made by Gerhard Reuter in Germany which uses flat Li-Ion batteries that are soldered in.  If you have no problem using soldering irons, then none of this is a concern.

I can live without on-board Bluetooth, since dongles are available online.  But I would like to see coverage of the full medium wave band and it would certainly be nice to have FM band coverage.   Obviously the ability to update the radio’s firmware would be a welcome addition.

Another suggestion I would make to Alex would be to provide some way to quickly move from band to band, similar to the capability seen on most regular portables.  Having to constantly press the side knob to switch to rapid 50 kHz slewing to move say, from 49 meters to 19 meters, involves too much fiddling.

It would be interesting to see the internals of the Belka radio – four Philips screws are located on the left and right sides of the receiver, so that should not be difficult, though I have chosen not to go exploring inside mine.

Summary

Overall, I am very impressed with the Belka.  This seems to be an amazingly quiet and sensitive little receiver.  It’s obviously similar to the CR-1a in that it has a display, but much smaller and perfect for Dxing on the road, with a BNC connector that enables connection of any amplified antenna, loops or longwires.

I have included a video made outside my house using only the BNC telescopic antenna with the Belka, showing reception at about 1800 to 1830 UTC of some major stations in the SW bands.

This demonstration shows how sensitive the Belka is in broad daylight hours (also shown is my SONY SW-1000T).

A search of YouTube shows at least two other handheld DSP receivers being demonstrated in 2019, both with full scope screens, seemingly experimental units and on Russian YouTube channels.  There is some discussion of availability, but as of early 2020 these units do not seem to be available.

It’s unclear whether any of these units ever made it to production on any scale.  Comparing the features on these to the Belka – including AGC, Noise Reduction, Squelch, etc – it seems there might be quite a bit of space on the open market for SDRs that far exceed the capabilities of the Belka.

On the other hand, inclusion of larger scope displays would clearly have implications for battery life, which is one area where the Belka SDR – with its claimed 24 hour duration – obviously excels.

I will be interested to read other user reviews of the Belka-DSP – for now, it appears to be the only receiver of its kind and size being produced in significant numbers, so I certainly want to thank Alex for bringing it to the market.


Thanks so much, Dan for sharing your review of the Belka-DSP. I agree that likely the reason the Belka-DSP is less prone to the effects of holding and grounding is because it has a metal case and is probably better shielded. I agree that there should be an easy way to move between the various meter bands. Including features like this is always a concern in terms of ergonomics for small radios with simplified controls.

It is a fascinating and unique little receiver. Since it’s designed and produced by a “mom and pop” company, I imagine upgrades won’t happen unless there’s a new version produced at some point. With that said, this engineer obviously has the know-how to make a capable receiver! 

Thanks again, Dan, and we look forward to any/all updates you wish to share!

Click here to check out the BelkaDSP product page.


Do you enjoy the SWLing Post?

Please consider supporting us via Patreon or our Coffee Fund!

Your support makes articles like this one possible. Thank you!

Spread the radio love

23 thoughts on “Dan’s initial review of the Belka-DSP portable shortwave radio

  1. Brian porter

    Was surprised at how fast it came.great little radio.would have liked mv but I can see where filtering would be a problem.band changing would be nice.nobody mentioned that it has i/q which is nice.if I had a chance would keep as my Xmas present.

    Reply
  2. Jerry Neves

    Hello to all.
    This little radio sounds exciting. My concern after reading the reviews is the battery, which apparently when needs replacement in the future has to be soldered! What happens if you can not solder? Send radio back to manufacturer in Europe?? Is there a connection in the unit for a power supply?
    Any clarifications on this will be appreciated.
    Regards to all.
    Jerry

    Reply
  3. Zach

    Am2 stands for pseudo synch mode
    You need to use stereo connector do audio or it will be damage
    From the user guide

    Reply
  4. Ken

    It seems like they should put a USB connector on it : not only for charging, but I think there is a “microcontroller” in there and there should be a way to connect to it (via serial port and “sound card”) to allow controlling and setting channels, etc.

    Reply
  5. Richard Langley

    “Another suggestion I would make to Alex would be to provide some way to quickly move from band to band, similar to the capability seen on most regular portables. Having to constantly press the side knob to switch to rapid 50 kHz slewing to move say, from 49 meters to 19 meters, involves too much fiddling.”

    As others have mentioned, and as I have confirmed with my receiver (received in 2 weeks from Minsk and the transaction using a Bank of Montreal MasterCard went through immediately without any problem), you can sacrifice some or all of the memories to enter band-edge frequencies to quickly switch from band to band.. Also, although the receiver does not have a line-out jack, the earphone/speaker jack can be used for recording with a suitable adjustment of the volume level.

    Reply
    1. Guy Atkins

      According to the Belka-DSP’s manual, pressing in the knob while tuning provides a greatly increased tuning rate– up to a 200 kHz step if the 1-50 kHz setting is already chosen.

      Reply
    1. Guy Atkins

      Many of the “cottage industry” SDR transceivers available do NOT offer full general coverage. Some stop above 2 or 3 MHz, or at 1.6 MHz. If they do tune into MW, reception is generally so filtered out that it’s useless.

      I owned a RS-918 SSB HF SDR HAM transceiver for a while. It’s a neat unit, but some specs say reception is from 0.5 – 30 MHz, and others say 1.8 – 30 MHz. Mine tuned down to 510 kHz but there was nearly zero signals to be heard in the MW range.

      I think the problem here is SDR architecture limitations, or the need for so much BCB high-pass filtering so as to make MW reception impossible. MW station energy can overload the HF range, and since these are mainly ham radio transceivers they need to add the filtering to make sure the ham bands receiver well.

      It’s a similar situation with the Elecraft KX3 that I owned when it was first released. Its medium wave reception is very poor, and not intended for DXing.

      So, I think the situation may be similar with the BELKA-DSP; filtering is needed otherwise HF performance is compromised. Too bad the filters aren’t switchable IN/OUT though!

      BTW, I received the BELKA yesterday, and it was quick shipping from Minsk with a tracking number. What a great little radio!

      Reply
  6. Guy Atkins

    My unit has left Minsk and is on the way to the USA per the tracking number. Ordering was very easy with my PayPal Mastercard, with no contacting a bank, etc., needed. It proceeded like a normal online purchase.

    Reply
  7. John Hagensieker

    I just purchased one and can confirm you have to call your bank. Visa flags the account, not your bank. Do one transaction, get it declined then call your bank. I use Navy Federal and it took like 5 minutes on the phone to have the bank contact Visa.

    Thanks for the great review. Looking forward to getting mine.

    Reply
  8. Harald

    Are the memories “tunable”? If so, you could store a frequency in each of the bands you are interested in into memories and start tuning inside the band from there.

    Reply
  9. Scott Gamble

    I just got mine in the mail today. (Im)Patiently waiting for it to charge, but it is a solid feeling little radio. Can’t wait to try it out. It’s coming with me to swlfest also!

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.