Tag Archives: Degen DE1103 Review

The New Degen DE1103 DSP: First impressions & review


When I discovered that Degen had recently refreshed the receiver design of the DE1103, I was intrigued, to say the least. The original DE1103 sported some serious performance for a sub-$100 receiver.


The 2015 model of the Degen DE1103 implements a DSP chip (the Silicon Labs Si4735-D60).

Yet I was on the fence about purchasing the new DE1103. Why? In truth, I never fell in love with the original DE1103. While I appreciated the 1103’s unique analog-style digital display, I never got used to its quirky ergonomics. Degen had quality control issues, too: I had to return two faulty units before getting one that worked as advertised (incidentally, I had a similar problem with the Kaito KA1102).

Then last week, SWLing Post reader, Ron, contacted me. He had purchased the new DE1103 from Hong Kong-based eBay vendor Bigbargainonline.


Ron kindly provided the SWLing Post with his impressions of the DE1103, as follows:

Performance is roughly on a par with the earlier dual conversion version. This one is just as hot, but no hotter.

If you were thinking a GP5 on a bigger ferrite bar, yes…and no.

There is one major gripe…[this unit] will not remember frequencies set with the BFO on, like the earlier dual-conversion version did. Instead you have to turn the BFO on for each memory frequency [for which you] need it.

One thing [I] noticed right off was the almost complete lack of AGC “pumping” on CW and SSB that all earlier versions had (yay!) but this plus comes at the cost of having the BFO “remembered” in memory.

Zero-beating (or centering) the BFO to null on WWV and local AM stations to check alignment was…strange. At null beat the BFO seems to quit for a second. It is fine
either side of zero beat, however.

This is doubtless due to Tecsun’s adapting the Silicon Labs IC to a full range BFO like this. Recall the same IC in the GP5 features Upper and Lower selection on CW/SSB.

This 1103 DSP version also has the GP5’s slight tuning mute, not a problem.

But for ease of operation in CW/SSB mode, the GP5 is [much] better IMO.

Ron also notes that he wasn’t pleased with the DE1103’s longwave performance and didn’t feel the mediumwave and shortwave reception was an improvement on the original DE1103.

He decided that he would sell this DE1103 and gave me first dibs, so I bit the bullet. I was eager to compare the new DE1103 with some of the other DSP-based portables in my collection. Ron dispatched the DE1103 immediately–it arrived a few days ago, but I didn’t have a chance to test it until yesterday.


I took the Degen DE1103 outside, sat it on the tailgate of my truck and put it on the air…

I tuned around the mediumwave band and picked up all of the local benchmark stations. Same with FM. So far, this tuning confirmed Ron’s assessment of the DE1103: it didn’t surpass the original.

But the shortwave bands were a different story.

As I tuned around the HF bands, the DE1103 seemed to receive quite a lot signals.  But in most instances, I could hear local AM broadcasters bleeding in, as well. Indeed, imaging was prevalent across the shortwave bands–the receiver was obviously being overwhelmed by a local broadcaster.  Unfortunate.

Could strong interference account for this? While there are local AM broadcasters around, they’re not exactly “blow-torch” stations. Indeed, I’ve never had overloading issues with other shortwave portables I’ve used in the same location–not even with my Kaito WRX911!

Imaging was prevalent on the DE1103 when it was tuned to pretty much any audible shortwave broadcaster.

Here’s a video of the Degen DE1103 tuned to the Voice of Greece on 9,420 kHz:

What you’re hearing in the audio is a local broadcaster bleeding in. Note that when I tune off-frequency, no imaging is heard.

Wondering if something had changed locally–and just to be fair–I pulled out my Sony ICF-SW100 and sat it next to the DE1103. The Sony had no issues.

This time, I tuned to WWV on the 19 meter band and compared the two receivers:

As Dan Robinson expresses it, the ICF-SW100 “wipes the floor” with the DE1103. There’s no hint of overloading in the SW100.

My buddy, Ron, is clearly a keen radio reviewer; obviously he didn’t hear overloading on the shortwave bands where he tested the rig, else he would certainly have mentioned it. The location where I tested the DE1103 does have some local broadcasters in the area, but no clear channel or high-power stations; in short, there’s no likely interference within a ten-mile radius to account for this debilitating performance problem.

Too bad…!

Obviously, the new DSP version of the Degen DE1103 is especially prone to imaging on the shortwave bands. In fact, it’s the only receiver I’ve ever tested that has overloading issues at this testing location (where I tested the original Degen DE1103, by the way).

My assessment? Avoid the new Degen DE1103.

A much better receiver with SSB for roughly the same price would be the venerable Tecsun PL-600 ($89.99 at Amazon and $89.95 at Universal Radio). If SSB reception isn’t necessary, you might also consider the CC Skywave or the very affordable Tecsun PL-310ET.

Spread the radio love