Tag Archives: G90

Review Notes: Xiegu GSOC Firmware updated to version 1.1–still a number of issues

For those of you who have been asking about the new Xiegu GSOC controller, I just updated my unit with the latest firmware (version 1.1).

Firmware notes show that it addresses the following items:

Xiegu GSOC FW V1.1
1. Solved the CW sidetone delay problem
2. Solved the problem of unstable system and occasional crash
3. Added RTTY modem
4. Added CW decoder
5. Added SWR scanner
6. Added FFT/Waterfall level adjustment
7. Added FFT line/fill color mixer

The list above was copied directly from the version notes.

I’m currently evaluating the GSOC/G90 pair which were kindly sent to me on loan by Radioddity. I upgraded the GSOC firmware to v1.1 this weekend.

What follows are some of my evaluation notes an observations after performing the upgrade.

Updating firmware

Updating the GSOC firmware is a pretty straight-forward process.

First you must download the GSOC firmware package (about 330 MB!) which includes a disk image and application to flash the image to a MicroSD card.

Yes, you’ll need a dedicated MicroSD card to upgrade the GSOC firmware–meaning, you can’t simply use a MicroSD card with data on it you’d like to keep because the process of flashing the ISO file also includes a full format with multiple partitions.

You’ll also need an SD Card reader/writer if your Windows PC doesn’t include one.

The included firmware application/tool makes it quite easy to flash a disk image on the MicroSD card.

After the MicroSD card has been prepared, simply turn off the GSOC, insert the MicroSD card on the left side of the GSOC, turn it back on and the GSOC will automatically boot from the MicroSD card and install the new OS/firmware.

Once the upgrade has completed, the GSOC will turn itself off and you must remove the MicroSD card.

If you want to restore the MicroSD card to one partition, you’ll need to perform another format and shrink the volumes.

CW sidetone latency (still issues)

After performing the upgrade, I hopped on the air and tried to make a few CW contacts since I noted in the version notes that the CW sidetone latency had been addressed. So far, my evaluation has pretty much been on hold because I’m unable to use CW mode with any sense of sending accuracy.

Unfortunately, I’m still finding that there’s still a bit of sidetone latency or keyer timing interfering with my ability to correctly send words and letters.

To my ear, it sounds like there’s much less latency in the sidetone audio now (compared with v1.0 which was a little insane) but I still struggle sending characters that end in a string of dits or dashes. For example, when I try to send a “D” the radio will often produce a “B” by adding one extra dit. Or if I try to send a “W” it might produce a “J”. I know something is a little bit off because I botched up two CW contacts with POTA stations yesterday as I tried to send my own callsign correctly.  And “73” was even problematic.

I’m guessing that there may still be a bit of audio lag between the G90 body (where the CW key is plugged in) and the GSOC (where the sidetone audio comes out). At the end of the day, the keying information must be sent to the GSOC from the G90 transceiver body and I assume the processor on the G90 is causing a bit of audio latency. Hopefully, Xiegu can sort this out. It’s a serious issue for anyone who wants to operate CW with the GSOC.

If you own the GSOC and operate CW, I’d love your comments and feedback.

Other updates

I tried using the CW decoder yesterday via the “Modem” menu and had limited success decoding a CW rag chew.

My markup in red: You can see at the very end of this conversation, it decoded the call sign, but interpreted “TU” as “TEA”

The decoder seemed to adjust the WPM rate automatically at one point, but as you can see in the image above, almost every dit was interpreted as an “E” and every dash a “T”. I must assume I don’t have it configured properly, but I don’t have an operator’s manual for reference and instruction.  I’ve also tried RTTY decoding, but haven’t been successful so far–I’m pretty sure this is also because I haven’t configured it properly.

SWR Scanner

I tested the new SWR scanner and it seems to work quite well, plotting SWR across a given frequency range. I did note, however, that it doesn’t seem to confine itself to the ham bands at all. It does inject a signal as it scans (I read 1.5 to 2 watts on my CN-801 meter).

I discovered out-of-band scanning when I took the photo above while trying to do a scan of the 30 meter band. It started around 9.6 MHz–well into the 31M broadcast band where it shouldn’t be transmitting. Xiegu needs to limit transmitted signal to the ham bands.

Memory Keying

I had hoped Voice Memory Keying would be added along with TX/RX recording. I do believe this will eventually be included in a future update. It appears via the “Modem” menu that CW Memory Keying has been added, but I can’t sort out how to make it work (again, a operation manual would be quite handy).

Audio recording

I had hoped transmit and received audio recording would be added in this firmware update; I understand this will eventually be added.

Combined current drain

As I mentioned in a previous GSOC update, the GSOC controller and G90 transceiver both need a 12V power source–indeed, each has a dedicated power port. The GSOC does not derive power from the G90.

I was originally told that the G90 and GSOC both pull about .60 amps in receive which would total 1.2 amps combined. My Hardened Power Systems QRP Ranger battery pack displays voltage and current; it’s not a lab-grade measurement device, but it’s pretty accurate. When I operate the GSOC and G90 at a moderate volume levels in receive, it appears to draw 0.95 to 0.97 amps–basically, 1 amp.

At home on a power supply, this is inconsequential, but in the field you’d need to keep this in mind when choosing a battery. It’s on par with a number of 100 watt transceivers.

Spectrum display images

I’m still finding images on the GSOC display that are not present in the received audio. I mentioned this in my initial overview and it doesn’t seem the firmware update addressed this.

I can only assume the spectrum imaging might be due to the I/Q input being too “hot” coming from the G90 via the shielded audio patchcord. Perhaps there’s a function to manually lower the I/Q gain, but I haven’t found that yet.

Spectrum images are most noticeable on the 31 meter band, but found them on the 20 meter ham band as well.

Here are two screen shots that show how images appear when a nearby signal overwhelms the GSOC:

Images are not present all of the time, only when a strong signal intrudes.

Ever-present noise and spurs in portions of spectrum

Perhaps this is related to the issue above, but there are some spurs on the spectrum display that seem to be present whether the G90/GSOC is hooked up to an antenna or dummy load.

Here’s a photo of the GSOC hooked up to an antenna:

And to a dummy load:

I’ve highlighted the spurs in red and as you can see, the intensity is stronger without an antenna thus I’m guessing this is internally-generated. The spurs do not move on the display as you change frequency.

Other notes

Again, I feel like the GSOC firmware isn’t mature and I can’t yet recommend purchasing it. I feel like Xiegu have rushed this unit to market.

I know that, over time, more features will be added and Xiegu certainly has a track record of following up.

When I evaluate a product, I keep a list of notes that I send to the manufacturer and to keep for my own reference. In Alpha and/or Beta testing, I’d share this info only with the manufacturer. Since the GSOC is a product that’s in production and widely available, however, I thought I’d share them here publicly:

  • GSOC volume control scale is 0 to 28. The difference between 0 (muted) to 1 seems to be the biggest increment. Volume 1 is actually a low to moderate volume level (i.e. a bit high).
  • Boot up time for the GSOC is 30 seconds
  • A keyboard and mouse or capacitive stylus are almost required for accurate operation. Many of the touch screen buttons are quite small and difficult to accurately engage with fingertip. The pointer seems to fall slightly below where fingertip makes contact on the screen.
  • Notch Filter seems to have no effect even after the v1.1 upgrade. There is no Auto Notch feature either.
  • I can’t seem to engage split operation even though there are A/B switchable VFOs and a “Split” button above the spectrum display. Using a keyboard and mouse doesn’t engage it either.
  • There are a number of announced features that I haven’t discovered including some WiFi and Bluetooth wireless functionality.
  • For field use, you must pack quite a bit of kit: the transceiver, the controller, CW key cable, microphone, serial cable, I/Q cable, G90 Power cable, and GSOC power cable. It would also be advisable to take a wireless keyboard and mouse especially if you plan to use any advanced functions like CW memory keying.
  • It doesn’t appear that you have CAT control of the GSOC which complicates digital operation. I believe many of us hoped the GSOC would make digital mode operation easier with the G90, but it hasn’t. Indeed, I assumed the GSOC would have an internal sound card for digi modes much like the Icom IC-7300 and IC-705. Use of VOX control is still  the best way to control transmit. I hope this can be upgraded else this would be a missed opportunity.
  • Since the v1.1 upgrade, the GSOC hasn’t crashed (it did frequently with the v1.0 firmware).
  • Not a pro or con, but I wish the AF Gain/Squelch was AF Gain/RF Gain like most HF transceivers. I’ve accidently engaged squelch twice which essentially muted audio. Pressing and holding the PO (Power Output) button opens the RG Gain control function).

The GSOC Universal Controller is an interesting accessory for the G90 and I’ve read comments from users that love the interface and added functionality.

If I’m being honest, I feel like I’m Beta testing the GSOC. I’ve yet to find a GSOC operation manual–this makes it very difficult to know if one has correctly configured the controller and engaged features/functions correctly. A quick start guide is included with the product, but it really only helps with connections and starting up the GSOC the first time. If you’re a GSOC early adopter, just be aware of this. Again, I’m pretty confident Xiegu will make refinements and include promised features in future firmware updates. I understand their software engineer closely monitors the GSOC discussion group as well. If you’re considering the purchase of a GSOC, I’d encourage you to join the GSOC group.

Questions? Comments?

As I said, I can’t recommend purchasing the GSOC controller yet. So much can change with firmware updates, however, I would encourage you to bookmark the tag GSOC to follow our updates here on the SWLing Post. I will update the GSOC controller each time a new firmware version is issued and until Radioddity asks for the loaner units to be returned. Again, many thanks to Radioddity for making this GSOC and G90 evaluation possible.

Feel free to comment with any questions you might have and I’ll do my best to answer them!

Spread the radio love

Comparing the Icom IC-705 and Icom IC-7300 with the Xiegu GSOC G90 combo

I was recently asked to make a table comparing the basic features and specifications of the new Xiegu GSOC/G90 combo,  and comparing it with the Icom IC-7300 and IC-705.

This is by no means a comprehensive list, and I plan to add to it as I test the GSOC. It doesn’t include some of the digital mode encoding/decoding features yet. I’m currently waiting for the next GSOC firmware upgrade (scheduled for November 20, 2020) before I proceed as it should add mode decoding, audio recording, fix CW mode latency, and add/fix a number of other items/issues.

Comparison table

Click to enlarge

Quick summary of comparison

At the end of the day, these radios are quite different from each other. Here’s a quick list of obvious pros and cons with this comparison in mind:

Xiegu GSOC G90 combo ($975 US)

Pros:

  • The GSOC’s 7″ capacitive touch screen is the biggest of the bunch
  • The GSOC can be paired with the G90 or X5101 transceivers (see cons)
  • The GSOC controller is connected to the transceiver body via a cable, thus giving more options to mount/display in the shack
  • The G90 transceiver (read review) is a good value and solid basic transceiver
  • Upgradability over time (pro) though incomplete at time of posting (con)
  • GSOC can be detached, left at home, and G90 control head replaced on G90 body to keep field kit more simple (see con)

Cons:

  • The GSCO is not stand-alone and must be paired with a Xiegu transceiver like the Xiegu G90 or X5105. The X5105 currently has has limited functionality with the GSOC but I understand this is being addressed. (see pro)
  • I don’t believe the GSOC can act as a sound card interface if directly connected with a computer (I will correct this if I discover otherwise). This means, for digital modes, you may still require an external sound card interface
  • No six meter coverage like the IC-7300 and IC-705
  • Quite a lot of needed cables and connections if operating multiple modes; both GSOC and G90 require separate power connections
  • At time of posting, a number of announced features missing in early units, but this should be addressed with a Nov 20, 2020 firmware upgrade
  • Replacing and removing G90 control head requires replacing four screws to hold in side panels and secure head to transceiver body (see pro)

Icom IC-7300 ($1040 US)

Pros:

  • Built-in sound card interface for for easy digital mode operation
  • Excellent receiver specifications (click here to view via Rob Sherwood’s table)
  • Possibly the most popular transceiver Icom has ever made (thus a massive user base)
  • Well thought-through ergonomics
  • Includes six meter operation and expanded RX frequencies (compared with G90/GSOC); high frequency stability

Cons: 

  • The heaviest of this group (con), but it is a 100 watt transceiver (pro)
  • Smaller display than the GSOC
  • Touch sensitive display (not capacitive like the GSOC)
  • Faceplate not detachable like the G90

Icom IC-705 ($1300 US)

Pros:

  • Built-in sound card interface for for easy digital mode operation
  • Excellent receiver specifications (click here to view via Rob Sherwood’s table)
  • Can use swappable Icom HT battery packs
  • Well thought-through ergonomics, but on that of the IC-7300
  • Includes six meters and VHF/UHF multi-mode operation with high frequency stability
  • Includes D-Star mode
  • Includes wireless LAN, Bluetooth, and built-in GPS
  • Weighs 2.4 lbs/1.1 kg (lightest and most portable of the bunch)

Cons:

  • No internal ATU option
  • Maximum of 10 watts of output power
  • The priciest of this bunch at $1300 US

In short, I’d advise those looking for a 100 watt radio, to grab the Icom IC-7300 without hesitation. It’s a solid choice.

If you’re looking for the most portable of these options, are okay with 10 watts of maximum output power, and don’t mind dropping $1300 on a transceiver, the Icom IC-705 is for you. You might also consider the Elecraft KX3, Elecraft KX2, and lab599 Discovery TX-500 as field-portable radios. None of them, however, sport the IC-705 display, nor do they have native VHF/UHF multimode operation (although there is a limited KX3 2M option). The IC-705 is the only HF QRP radio at present that also has LAN, Bluetooth, and built-in GPS. And, oh yes, even D-star.

If you’re a fan of the Xiegu G90 or already own one, give the GSOC controller some consideration. It offers a more “modular” package than any of the transceivers mentioned above in that the controller and G90 faceplace can be swapped on the G90 body. The GSOC screen is also a pleasure since there are two USB ports that can connect a mouse and keyboard (driver for mine were instantly recognized by the OS).  The GSOC/G90 combo is a bit “awkward” in that a number of cables and connections are needed when configured to operate both SSB and CW: a CW key cable, Microphone cable, I/Q cable, serial control cable, power cable for the GSOC, and a power cable for the G90.  This doesn’t include the cables that might be needed for digital operation. I dislike the fact that the CW cable can only be plugged into the transceiver body instead of the GSOC controller like the microphone. Still: this controller adds functionality to the G90 (including FM mode eventually) that may be worth the investment for some.

Did I miss something?

I’ll update this list with any obvious pros/cons I may have missed–please feel free to comment if you see a glaring omission! Again, these notes are made with a comparison of these three models in mind, not a comprehensive review of each. I hope this might help others make a purchase decision.

Spread the radio love

Using the new Xiegu GSOC and G90 transceiver combo for shortwave broadcast listening–?

Listening to Radio Prague via WRMI with the Xiegu GSOC

Many thanks to SWLing Post contributor, Tim R, who writes:

Dear Thomas,

First of all thank you so much for the all of the energy you put into the SWLing Post. When crazy things are happening in the world it’s a very welcome sanctuary! Sending you some coffee money.

I plan to become a ham radio operator next year. Bought the book last week and once I finish a large project for work, I’m on it. Of course, the Tech license will only give me limited exposure to HF, but I’m already plotting an HF radio purchase because I can’t WAIT do do some SWLing with it. Up to this point, I’ve only owned portable radios and never really have used external antennas other than some cheap wire.

My question…

I’ve been considering grabbing a Xiegu G90 because it seems to be a nice comprehensive beginner’s HF rig and is very affordable. I read your review and understand your caveat that there’s no way to completely disengage the transmit so that it can’t be accidently hit if connected to an RX only antenna. I’m not worried about that because I’m going to hang a G5RV wire antenna and use it both for TX and RX. No problem if RF is accidently sent through it.

Of course, there’s a lot of buzz in the Xiegu community about the new GSOC controller. I had not planned to exceed $600 for my radio purchase, but I love the idea of the controller. But when I add $550 for the controller and $450 for the radio, all the sudden I’m at $1,000.

After some deep soul-searching (and let’s be frank here, a blessing from my wife and CFO) I’ve decided to raise my budget to $1,000.

All of this to ask, if you had $1,000, would you buy the G90 and GSOC controller, or would you get something else keeping in mind I want to use this as much for shortwave listening as for future ham radio work?

Any advice would be appreciated.

-Tim

Thanks for your question, Tim! And thanks for giving me a complete picture of your budget/radio requirements and the antenna you plan to use.

I’ll try to answer your question here, but understand this is more what I would do if I were in your shoes. This is a pretty simple question, but not simple to answer because there are so many options on the market.

Xiegu GSOC and G90 combo option

Keeping in mind, I feel like the GSOC is a work in progress at the moment and not fully developed–check out my initial review. Once the next firmware update is available it could certainly solve a number of small issues I found with the unit. It works, but it’s not a refined product yet.

It’s ironic, actually. When I received your message this morning, Tim, I was SWLing with the GSOC and G90–listening to Radio Prague on WRMI. In the end, though, the GSOC is primarily an enhanced interface for the G90. While it does add some extra functionality (and should, over time, add much more) it doesn’t really change the performance characteristics of the G90. I’d check out my G90 review for more info about performance.

Would I purchase the G90/GSOC combo if I were in your shoes? Again, it’s early days, so I don’t feel comfortable making a recommendation call yet. The G90 is, without question, a great value at $450 (often even less) investment. I like it primarily as a field radio, though, and once you add the GSOC to the mix, it’s a little less portable because it’s two units with quite a few interconnect cables. Of course, you can swap the GSOC unit for the G90 control head at any time, but that involves attaching and re-attaching the control head each time (there’s no accessible serial port on the back of the G90, for example)

If you’re a huge fan of the G90, the GSOC should eventually be a worthy addition. At present, for your use as a new ham and for SWLing, I’d perhaps consider other options too.

The Icom IC-7300

The Icom IC-7300 SDR transceiver

Since you’ve raised your budget to $1,000, I’d consider adding the Icom IC-7300 to your list. At present, via Universal Radio you can buy a new IC-7300 for a net price of $1039.95 after rebates. Sometimes, the price will go even lower although during the C-19 pandemic, I think that’s less likely to happen since supplies are lower than normal for many items.

The IC-7300 has better performance specs than the G90 and can output a full 100 watts if you like. The display is touch sensitive rather than capacitive like the GSOC. The display is also much smaller than that of the GSOC. The IC-7300 has a lower noise floor than the G90.

I think the IC-7300 is a great radio for SWLing, but the audio for broadcasts is sort of “flat.” You might check out this post where we did some audio comparisons. It does have native broadcast recording to an SD card, which I love. The GSOC should be adding this soon, too.

I would include the new Icom IC-705 as a recommendation here, too, but it’s $300 over your budget.

A PC-connected SDR and separate transceiver

 

This might be the option I’d take if I were in your shoes.

Get the 20 watt Xiegu G90 ($450) as planned or consider a radio like the 100 watt  Yaesu FT-891 ($640), Both of these radios are general coverage and would serve you well for SWLing and ham radio activities. I’d personally invest the bit extra and get the FT-891 since it would also give you 100 watts output and even has advanced features like memory keying.

We actually mentioned both radios in a similar post this year.

If you buy the pricier Yaesu FT-891, you’d still have $360 to invest in your shack!

I’d then buy an Airspy HF+ Discovery ($170–my review here) or SDRplay RSPdx ($200–my review here) and get all of the benefits of a PC-connected SDR.

These SDRs would take your SWLing to the next level. They have uncompromised performance for the price.

Both companies continuously improve their products/applications based on customer feedback. Indeed, check out some of our recent posts about SDR# free upgrades. Mind blowing stuff–!!!

You could even use the SDR as a panadapter for your transceiver which would give you the ability to have a full-screen spectrum display on an external monitor at home.

More options?

Of course, these answers only scratch the surface. I haven’t even included used, late model gear in these recommendations.

I’d like to give you a firm recommendation about the GSOC and G90 combo, but I’m waiting to see how this next firmware upgrade goes–early days still.

Post readers: Please comment if you have even more options/suggestions for Tim. What works for you within a $1,000 budget.

Spread the radio love

A review of the Xiegu G90 general coverage transceiver

The following review of the Xiegu G90 originally appeared in the August 2020 issue of The Spectrum Monitor magazine:


A comprehensive review of the Xiegu G90 general coverage transceiver

My coming of age in the world of radio was during the era of big US and Japanese radio manufacturers.  Icom, Kenwood, Yaesu, JRC, and Ten-Tec––these were the icons of my youth. And, I freely confess, I developed a partiality for their products.

So when incredibly inexpensive transceivers from manufacturers in China started showing up on the market a little over a decade ago, I was…well, skeptical. Very.  Many of these radios were a fraction of the cost we had been paying, and some models looked like direct copies of radios that were already on the market…but these copies were all-too-often second-rate either in features or performance.

Thus, as it was my policy to invest in quality products, I continued to put my money toward US, Japanese, and European legacy manufacturers that I felt would be here for the long haul in the amateur radio and SWL communities.

Had I become a bit of a radio snob? I admit it…maybe I had. But in truth, I was simply waiting for a quality Chinese-made radio to come along and change my viewpoint.

Times have changed

Recently, I compiled a list of general coverage QRP transceivers for the SWLing Post. My buddy Eric (WD8RIF) pointed out that I neglected to include any of the Chinese-made Xiegu brand transceivers, all of which offer general-coverage receiving.

I know a number of hams who use Xiegu (pronounced roughly “SHEH-goo”) brand portable transceivers for Parks On The Air (POTA) and Summits On The Air (SOTA) activations, and like them very well.  So I decided to waive my doubts and check out Xiegu’s transceivers. I found myself intrigued with one in particular: the G90.

The Xiegu G90

At time of publication, there are three Xiegu models widely available: the G1M, X5105, and the G90.

The GM1 ($260) is a compact, four-band 5-watt QRP transceiver, while the X5101 ($520) is a 160M-6M 5-watt Double Conversion Superheterodyne QRP transceiver. Both look promising, but the G90 is a 20-watt 160M-10M transceiver sporting a 24-bit 48 kb/s sampling analog-to-digital/digital-to-analog converter at just $450. That’s the one I chose to investigate.

I found both the G90 receiver specs and 20-watt-output power very appealing, especially considering the modest $450 price tag. But I found this receiver has other impressive features:

  • Detachable faceplate with included separation cable
  • Full-color backlit display with both spectrum and waterfall
  • Built-in side panel extensions to protect the front face and back of the radio
  • General coverage receiver (0.5~30MHz) in SSB/CW/AM
  • Built-in automatic antenna tuner (ATU)

About the only feature the G20 doesn’t include is an option for a built-in battery pack. Certainly not a deal-breaker by any means, since more often than not I use an external LiFePo battery for field-portable radio work.

I made up my mind to bite the bullet and purchase the G90. I was incredibly curious whether it could compete with my Elecraft KX3 and/or KX2, and I also wanted to explore the capabilities of its general coverage receiver for broadcast listening.

I placed an order with US distributor MFJ Enterprises for a total cost––including shipping––of $467.95.

Initial impressions

I tend to review ham radio transceivers around the time they hit the market. One of the unique advantages of being one of the first people to review a transceiver is that I really have no idea what to expect in terms of performance, other than perhaps what the manufacturer’s reputation has taught me over the years. And if the manufacturer is fairly new to me––? Then it’s truly a roll of the dice.

The G90, however, had been on the market for quite a few months, so I simply avoided reading any in-depth reviews so I could form my own opinions. With that said, I knew in advance that this radio is already well-loved by a very active and enthusiastic community of amateur radio operators. So I had only to make up my mind, myself. I got to work.

Form-factor

When I first removed the G90 from its box, I was struck by its weight, build quality, and size. First off, it’s a heavy little radio. The Xiegu site notes that the weight of the radio is about 2.2 lbs (1 kg), but perhaps due to its compact size, it felt heavier to me. Indeed, when I placed it on my postal scales, it came in closer to 3 lbs 10 oz. Still a very reasonable weight for a portable radio, but a bit heavier than described.

Speaking of size, the G90’s shape is pretty unique. Looking at the radio head-on, it’s reminiscent of most portable QRP transceivers (like the CommRadio CTX-10 or Yaesu FT-818, for example) meaning that the front face is compact. The depth of the radio, though (or length, depending on how you look at it), is about 8.3 inches––or nearly 10” if you include the side panels––equivalent to many of my 100 watt radios.

The build quality of the G90 is truly impressive. Holding it in your hand, you feel like you’ve acquired a quality piece of kit. The chassis is very durable, the buttons have a tactile response, and both the front and rear are protected by built-in side panels (typically side panels would be a third-party addition for most radios).

Audio

Audio from the internal speaker, which is mounted on the top of the radio, is loud and punchy, a desirable attribute for a field radio. Better yet, when you port the audio to an external amplified speaker (headphone jack is on the left side of the radio head), fidelity is superb.

Display

The color TFT LCD screen measures only 1.8,” one of the smallest I’ve ever tested on a radio, but Xiegu did an admirable job laying out the interface so that it’s easy to read at any viewing angle. If you wear reading glasses to read a book, you’ll need them to read this display––some of the numbers and labels are tiny, but very sharp, crisp, and high contrast. I’ve had no difficulty whatsoever reading the display in the field.

What’s more, the spectrum display and waterfall are responsive and in real-time––there’s no delay or averaging which I especially appreciate when chasing CW and SSB signals. Although at first blush one might think the spectrum and waterfall are just too small to be useful, that would be a mistake. I was guilty of this prejudice myself, and now find I rely on the spectrum display to help locate unused frequencies, spot someone calling CQ, and even identify the relative proximity of an adjacent signal. Truly a helpful feature.

Bail

Unfortunately, there’s one very conspicuous omission on the part of the G90 designers: it has no bail nor feet of any sort to support the front of the radio and angle it for ergonomic operation. Herein lies my biggest criticism of this radio, because it truly needs something to prop up the front of the radio for comfortable operation, not to mention, to allow the bottom of the radio to dissipate heat effectively.

There are a number of third-party producers that will supply a bail for the G90, but many are clunky and expensive, and I feel an attached/integrated bail is always best.

Ad hoc solutions to the fore: in the field, I simply prop the G90 on my
Bioenno 15 aH LiFePo battery; in the shack, I use a small support stand I purchased for my Elecraft KX3. Not as good as a purpose-made bail, but this works.

Microphone

The microphone that accompanies the G90 is what you would expect from a mobile HF rig: almost all functions can be controlled by its backlit keypad. I have read a few reports of people dropping and breaking the supplied mic. Turns out, the Mic’s 8-Pin Modular Plug is configured like a number of Icom radio models, and a replacement mic can be purchased on Amazon for about $22.

Remote head

As mentioned earlier, the control head of the G90 can also be separated from the body for use in mobile applications such as a car, RV, or even in the shack. The real surprise here is that the separation cable is included in the package. I’m not sure I’ve ever owned a mobile radio that came with a separation cable––what a luxury! Great addition.

Internal ATU

Another surprise for a radio in this price class: the G90 has a built-in automatic antenna tuner (ATU). When I first made the decision to purchase and review the G90, I didn’t realize this, and in fact would have never guessed it to be a possibility in a $450 transceiver. What’s more, this ATU is one of the best I’ve ever used in the field: it’s quick to match, and seems to find a match with almost any setup. I almost wish Xiegu sold a stand-alone portable ATU so I could use it with my other radios that lack an internal ATU.

Power output

Unlike most of the portable transceivers on the market that have maximum output power of around 5-15 watts, the Xiegu G90 will pump out up to 20 watts. While 90% of all of my ham radio communications are accomplished at 10 watts or below, I’ve appreciated a little extra “juice” while operating in the field.

Note: due to the speed of my phone camera, not all of the LED segments of my battery pack are visible.

With all that’s packed into this transceiver, no wonder it’s a heavy little unit!

My conclusion here is that the G90 feels like a quality rig. But how does it perform? Let’s first take a look at how I evaluate the transceiver as a ham radio operator, then as a broadcast listener and SWL.

Ham Radio Operation

Over one month of operating the G90, most of that time has been in the field, as I’ve taken the radio along for a number of Parks On The Air (POTA) field activations. Although I’ll be commenting about the G90’s performance as a transceiver in general, keep in mind that I do so mainly through the eyes of a field operator.

Although I often dislike operating compact radios due to small buttons and complex embedded menus that supply knobs and buttons with multiple duties, I find operating the G90 surprisingly pleasant. All of the most important functions of the transceiver can be called up with one or two button presses. Obviously, a real ham radio operator played a part in designing the G90’s operation.

Tuning the G90 is a simple process. The main encoder, of course, allows you to tune up/down the band. By short-pressing the encoder knob, you can change between the hundreds, tens, ones, tenths, and one-hundredths of a kHz. In fact, it’s very simple to move around a band this way. The encoder action is defined by detents that you feel as you rotate the knob. Normally I’m not a fan of detents on a radio’s main encoder knob, but since this one is so small, I think I actually prefer it as a means to control the spinning action. There is no brake adjustment.

Upgraded G90 Encoder

The supplied encoder knob is made of plastic and has dimples on the front to give your finger a bit of grip as you tune up or down. Upon the recommendation of a friend, I purchased a third-party dimpled aluminum knob to replace it––a major upgrade for a modest $8 investment!

Changing between bands and modes is very simple with the G90. There are dedicated band and mode up/down buttons on top of the radio’s front panel much like those on the venerable Yaesu FT-817 and 818 series. The G90 defaults to ham radio band allocations, but there is a menu setting that allows you to also include broadcast bands between band changes. Nice touch.

There is a dedicated AF gain control on the front of the radio. After receiving the radio, I was disappointed by the lack of an RF gain control, something I use a lot during noisy band conditions. Fortunately, Xiegu included an RF Gain control in one of the latest firmware updates: to access it, simply press and hold the AGC button, then make adjustments to the RF Gain percentage with the main encoder. The G90 defaults to a 50% setting. While I’m not really sure what this setting means, I do find the RF gain control quite effective, even though it doesn’t respond like a legacy receiver’s RF gain control.

The Xiegu G90 has a simple and effective variable-filter control: simply press the FUNC button then the CMP button, and use the encoder to adjust the low end of the filter.  To adjust the high end, press the FUNC and NB button in the same way. I love the fact that the filter can be adjusted from both the high and low ends, and that it’s variable instead of set at predetermined fixed widths such as “wide” and “narrow.”  All mode filters are adjusted in this fashion.

CW Mode

The G90 is a capable CW transceiver and should please the CW operator. The keyer speed, ratio, auto modes, and paddle setup are all accessible from the KEY function button. By pressing the FUNC and Key buttons, you can access the CW volume and tone parameters. The G90 also allows you to turn on a QSK function and adjust the hang time. The G90’s version of QSK isn’t the full-break-in variety you might find in, say, the Elecraft KX series radios. Meaning, while the hang time is very short, if sending at high speed you won’t be able to hear another station break in between your characters. You will note a slight relay click. With that said, I find the QSK mode to be quite effective for my use because I’m not really a “full-break-in” kind of operator.

The yellow CW tune LED on the front of the G90. Some might find it distracting if engaged.

Speaking of CW, the G90 features a CW tune feature that indicates when you’ve locked onto a CW signal: a yellow LED will flash as CW is received. While I find this feature a bit distracting, I’m sure some operators will appreciate it. In addition, the G90 features a CW reader that will decode CW when a station is properly tuned in and isolated from others.

Note the CW decode at the bottom of the display.

In the field, this feature has helped me confirm call signs––but like most transceiver CW readers, it’s not always accurate, especially if the CW operator on the other end uses a hand key or bug. Still: a welcome feature.

SSB mode

Most of my operating time on the G90 has been in SSB mode, and I’ve been very pleased with the radio’s performance in this mode. The G90 allows you to adjust the mic gain and enable compression. I’ve gotten excellent audio reports from the numerous SSB contacts I’ve made on the G90.

I should note here that although I feel you get much more radio than you pay for with the G90, I do wish it had a voice keyer. Especially when I’m activating a park via POTA, I call CQ a lot. With my Elecraft KX3 and KX2, for example, I set the voice keyer to “beacon” mode which allows me to pre-record a CQ and have it playback the message on a loop with a few seconds in between to allow me to recognize anyone replying to my call.  I rely so heavily on this feature for SSB park activations, just to save my voice, I know the G90 can never displace my Elecraft field radios. Again, I wouldn’t expect such a feature in this price class, but it would make for a near ideal field radio.

Digital modes

One thing that surprised me about the G90––especially since it is an SDR––is that operating digital modes is less “native” than I would have expected. Many modern SDR transceivers make setting up for modes like FT8 relatively easy with both CAT control and often the radio itself is identified as a sound card, thus no external interface is needed. When I decided to try running FT8 on the G90, I was discouraged by the fact that setup is much more like that of a legacy radio. Indeed, many users have had communication issues with popular software packages.

Since I wanted to test the G90 as a field radio and since I do very little FT8 in the field, I simply omitted testing this functionality. I have read that many operators have, of course, been able to successfully use the G90 for digital modes, but be prepared to read through the G90 email discussion group (see link at end of article) for best practices.

Update: SWLing Post contributor, David White, brings up one fine point about the G90’s VOX control. “I use that feature for TX control when running any of the digital modes with the laptop audio in/out going through the rear AUX connection.” Thanks for pointing this out, David. VOX control really facilitates using digital modes because the radio can detect audio comping from the computer and engage transmit without having to use CAT control of any sort.

Receiver Performance

Overall, I’m favorably impressed with the G90’s receiver. Both sensitivity and selectivity are above par, especially for a radio in this price class. The G90’s noise floor is acceptable, though not as low as that of my Elecraft radios. I do find that with the G90, I often need to ride the RF gain control in our noisy summer band conditions. I find that by adjusting the RF Gain and selecting the most effective AGC setting, I’m able to achieve an excellent signal-to-noise ratio. I find the G90 audio a bit fatiguing when I’m operating for long periods of time–at least, compared to some of my other transceivers.

In a nutshell: the G90 packs a lot of performance in an affordable radio, especially if you’re willing to tailor the filter settings, AGC, and RF gain to best accommodate the conditions.

Field notes

I’ve been very pleased with how long I can operate on battery power with the G90. Even with the display backlit set to 80% and with the volume set to high, I found that the maximum amperage the G90 would consume was about 0.60 amps. While I wouldn’t consider that benchmark, it is respectable.

I also like the G90’s built-in antenna analyzer. By pressing and holding the POW button, the G90 will display a graph showing the SWR figures across your specified frequency range. A brilliant and handy feature in the field! It’s important to note, though, that during the test the radio is transmitting a little RF so don’t try it with a receive-only antenna.

I do find that the G90’s body gets pretty warm–downright hot–when activating a park. It’s no wonder, really, because I often end up calling CQ at five second intervals over the course of 60-90 minutes on average.  That’s demanding a lot of a fanless radio, thus it gets very warm to the touch. Still, while I never had any overheating issues, I’ve also never operated the radio in direct sunlight for extended periods of time and I’ve always propped up the radio so that air can flow underneath the chassis. Again, if for no other reason than to dissipate heat, Xiegu should have incorporated a bail or folding feet. As much as I love the front and back panel extension, I would have chosen a bail over these.

Broadcast listening

While broadcast listening is often an afterthought for most ham radio operators, it never is for me. I like to travel lightly and I like my QRP transceiver to double-duty as a tool for SWLing.

From day one, I have spent a great deal of time with the G90 across the broadcast bands.

Shortwave

One of the main reasons I decided to review the Xiegu G90 is because I found so little information out there about how well the general coverage receiver worked for HF broadcast listening.  The G90 has a frequency range of 0.5-30 MHz (SSB, CW, and AM).

But I couldn’t find a specification showing the maximum width of the AM filter. In a few display photos with the AM filter width was indicated as 5.4 kHz––if this was so, I concluded, it was fairly workable if not particularly wide. However, only moments after opening the box and putting the G90 on the air, I tuned to the Voice of Greece (9,420 kHz) and learned how to change the AM bandwidth.  I was very pleased to find that in AM mode, that indicated filter width is only half the actual width: this means the G90’s AM filter can actually be widened to 10.8 kHz––brilliant!

In short, I’ve been very pleased using the G90 for shortwave broadcast listening; it has exceeded my expectations. I find that in terms of both sensitivity and selectivity, it offers performance on par with a dedicated receiver.

For an idea of how the G90 sounds on shortwave with its internal speaker only, check out the following videos:

The Voice of Greece

Radio Nacional De España

Broadcast listening is basic with general coverage transceivers: the G90 has no synchronous detector with selectable sidebands, for example. G90 users have requested this feature in a future firmware update, but I wouldn’t hold my breath in anticipation. I imagine G90 developers will be more concerned with ham radio-specific functionality.

Mediumwave

Let’s face it: Asking the G90 or any ham radio transceiver to perform on the mediumwave/AM broadcast band is asking it to do something it was never designed to do.

With that said, I have been very pleased with the G90 on the AM broadcast band.

Audio fidelity is excellent, especially with the AM filter widened appropriately and when using an external speaker or headphones.

The G90 performs so well between about 900-1700 kHz, I have even done some proper mediumwave DXing with it.

Below 900 kHz, I’m still able to tune strong and weak stations, but I have found some odd behavior with imaging as I tuned down to 500 kHz: some stations would move across the spectrum display in the opposite direction to which I was moving the encoder. I suspect this may be due to a very strong local station near me on 1010 kHz that was overloading the front end.

Again, however, I never expected any reasonable performance on mediumwave–especially since many transceiver manufacturers intentionally attenuate those frequencies, so I’ll accept any quirks it may have here and consider any G90 mediumwave functionality at all simply icing on the cake.

Important caveat for the broadcast listener

While, overall, I’ve been super pleased listening to the shortwave and mediumwave with the G90, there is (at time of publishing) a major drawback for anyone who would like to use the G90 exclusively as a stand-alone receiver: there is no way to completely disable the transmitter. 

The lowest power setting on the G90 is 1 watt. While that’s not a lot, it’s more than enough to fry your amplified magnetic loop antenna, for example. So, please use caution.

Although you could make it more difficult to transmit by not hooking up the microphone or a key (of course), there’s no way to disengage the internal ATU. If you accidentally press and hold the TUN button, it will engage the ATU and transmit.

In addition, if you press and hold the POW button, you will engage the antenna analyser function which will also inject RF as it sweeps across the bands testing the antenna’s standing-wave ratio.

Based on a suggestion, I even tried setting up the G90 in split mode with the transmit frequency set well outside the meter band I was operating.  I thought by having the transmit frequency out-of-band, it would keep the radio from transmitting. Turns out, I discovered a bug in the G90. When you perform this procedure, it essentially bypasses the safeguards that keep an operator from transmitting out-of-band. Since this is public now, I assume it will be addressed in a future firmware update.

And, as careful as I am as an operator, I would never hook my G90 up to an active receiving antenna for this very reason. While I’m sure there’s probably a hardware modification to kill the transmitter section on the G90, it would be brilliant if Xiegu developers include a function via a firmware update to snuff transmit.  At the very least, perhaps they could devise a way to disengage the ATU and antenna analyser functions via firmware.

Summary

Every radio has its pros and cons. When I begin a review of a radio, I take notes from the very beginning so that I don’t forget my initial impressions and observations. Here’s the G90’s list, from the first moments I turned it on to the time of writing this review:

Pros:

  • Amazing “bang-for-buck”––a lot of radio for the money
  • Crisp, easy-to-read backlit color display
  • Detachable control head, cables included
  • Built-in side panel protection for head and back
  • AM broadcast listening
    • Excellent shortwave reception
    • Capable mediumwave performance
  • 20 watts power output
  • Mic can control all-important radio functions, including direct frequency entry
  • Very good audio from internal speaker

Cons:

  • No built-in bail
  • No manual or auto notch filter
  • Very few options for customizing the display
  • (Minor) Firmware updates must be made to faceplate and transceiver body separately
  • MW: some weird functionality below 800-900 kHz (eg, images in opposite direction)
  • No voice keyer
  • No CW memory keyer
  • No internal battery option
  • Cannot lower power output below 1 watt, cannot disable transmit
  • Bottom of chassis gets hot during prolonged periods of operation
  • ARRL and Sherwood testing shows key clicks in transmit
  • Received audio a bit fatiguing over long listening sessions

Conclusion

Despite the shortcomings above, I have to say: the Xiegu G90 has exceeded my expectations, and then some.

Without a doubt, the G90 is a solid radio and a steal at $450 US. If you’ve always wanted a field-friendly portable transceiver, but didn’t want to shell out a lot of money, you can buy the Xiegu G90 for the same price you might pay for a two year-old iPhone. Impressive.

Although the G90 is a budget radio, it doesn’t play like one. Performance is on par with a radio twice its price and not only does it pack a lot of extras––like an internal ATU, mobile-worthy control microphone and detachable faceplate––those extras actually work just as they should. Nothing about this radio feels “cheap.” In fact, I’d be more inclined to call it a little workhorse of a radio.

To answer a question I asked myself early in this process: will the G90 displace my Elecraft KX2 as my field radio of choice? No, but that’s because I already own the KX2 and find that it fits my operating style better than any other transceiver I’ve owned thus far. Yes, I still prefer the KX2’s operation, performance and versatility over that of the G90–it’s more refined–but the former is more than twice the price when similarly configured.

I think the G90 would also make for a stellar beginner’s radio, as it is a totally self-contained station; simply apply power, and play!

In short, I’m pleased to report that I’ve finally found a very affordable radio that’s a basic solid performer, and I look forward to further offerings from Xiegu.

Resources

Retailers


Do you enjoy the SWLing Post?

Please consider supporting us via Patreon or our Coffee Fund!

Your support makes articles like this one possible. Thank you!

Spread the radio love

Which would you choose as a first radio–the Icom IC-7300 or Xiegu G90?

Many thanks to SWLing Post contributor, Paul, who writes:

This came to me from a friend; he is curious about choosing between the Xiegu G90 and the Icom IC-7300 for his first rig. He has money to buy the Icom which is $999 right now after rebates, but wants to know if he is really getting twice the radio for the Icom, vs the Xiegu, or are there other good reasons to get the 2016-introduced Icom, vs the newly introduced Xiegu.

Maybe this can be a posting to ask your readers? Greatly appreciate it.

Thanks very much
Paul

Thank you for passing along the question, Paul.

While I almost consider this to be an “apples to oranges” question, let’s approach this from a couple of different operator perspectives and truly explore the decision.

I like both radios for different reasons, but first, I’ll tell you what my decision would be if I were in in his shoes…

The Icom IC-7300 SDR transceiver

I would choose the Icom IC-7300

While the Icom IC-7300 does cost twice the amount of a Xiegu G90, it’s a much more versatile transceiver. There are almost too many IC-7300 features to list here, so I’ll mention a few that immediately come to mind, focusing on features the G90 lacks.

For one thing, the IC-7300 is a 100 watt radio, thus the max rated power output is five times that of the Xiegu G90.

The IC-7300 doesn’t require an external sound card for digital modes. Simply plug the radio into you PC with a USB cable, and with your favorite application (like WSJT), you can operate any number of digital modes. (I found configuring the G90 for digital modes to be a bit frustrating.)

The IC-7300 also covers the 6 meter band–the G90 tops out at 10 meters.

The IC-7300 has useful features for contests and field operation like:

  • voice and CW memory keyers with beacon mode,
  • native transmit and received audio recording,
  • a large touch screen display to quickly enter frequencies and adjust settings,
  • audio EQ on both transmit and receive,
  • a built-in bail
  • notch filters and Icom’s twin passband tuning

Again, by no means is this a comprehensive list–just some of the features that come to mind.

As a first rig, the IC-7300 can take you into any aspect or mode of the HF band your friend cares to explore. It must be one of the most popular HF radios on the market right now, so there’s also a massive user and knowledge base out there on the web.

The IC-7300 also has better transmitter specs, producing a cleaner signal than the G90, especially in CW (the G90 is known to produce key clicks and not recommended for use with an amplifier). It also can handle close-in signals better than the G90 and has a higher dynamic range. Overall, it has better specs than the G90.

For a more detailed look at the IC-7300, check out my full review.

Why one might choose the Xiegu G90 over the Icom IC-7300

The Xiegu G90 with upgraded encoder

Let’s get an an obvious point out of the way first: the G90 costs half that ($450) of the IC-7300 (generally $900-1,100). This could leave your friend with even more money to invest in an antenna. As I’ve said so many times before, a radio is only as good as its antenna!

If your friend plans to operate primarily in the field, the Xiegu G90 is much more portable option. The G90 is very compact and weighs a fraction of the IC-7300. The G90 also draws less current in receive mode, so is much kinder on a battery. It also has built-in side extensions to protect the front and back panels while being transported.

The Xiegu G90 has a detachable face plate which would come in handy for mobile installations (although, admittedly, there are a number of better mobile transceivers on the market).

My full review of the Xiegu G90 is in this month’s issue (Aug 2020) of The Spectrum Monitor magazine. It’s nearly a 4,000 word review so is one of the longer ones I’ve produced. If your friend wants to make a decision soon, he/she might purchase this issue to fully explore this rig.

Another option: Yaesu FT-891 and LDG Z-11 Pro 2 external antenna tuner combo

If your friend is seriously considering the Xiegu G90, then I have to assume he/she has portable operation in mind.

Making this assumption, I would also suggest they check out the Yaesu FT-891. Like the IC-7300, it has a full 100 watts output and also covers the 6 meter band. Like the G90, the front panel can be separated from the radio body for easy mobile installation.

Although I have never reviewed the FT-891 (although I plan to before the end of the year), the radio has an almost cult-like following among SWLing Post readers. It’s also a favorite rig of Parks On The Air (POTA) activators because of its 100W output, relatively compact footprint, and great audio characteristics. The G90 and IC-7300 both are based on SDR architecture, the FT-891 is a triple conversion superheterodyne general coverage receiver.

Unlike the IC-7300 and G90, however, the FT-891 lacks an internal antenna tuner (ATU) and I’m guessing your friend wants one based on the fact both the G90 and IC-7300 have one.

The LDG Z-11 Pro 2 ATU

No problem! The Yaesu FT-891 is one of the best bang-for-buck transceivers on the market. The price at time of posting is $609 after rebates. That leaves room to purchase a benchmark portable HF+6 meter antenna tuner. I personally love the LDG Z-11 Pro 2 which would only set them back $169. I’ve owned one of the predecessors of this ATU for nearly a decade. It’s located outdoors, in an enclosure and serves as a remote antenna tuner for my multi-band sky loop. It has operated flawlessly through seasonal temperature extremes and powered by a 15 year old  12V gel cell battery that is charged off of a 5 watt PV panel and Micro M+ charge controller.

The FT-891 and Z11 Pro 2 ATU combo would total $778 which is a nice compromise between the $1,000 IC-7300 and $450 G90.

If your friend wanted a more compact option than the IC-7300, and better specs and more power output than the G90, this FT-891/Z-11 Pro 2 combo would be hard to beat.

Don’t Forget Antennas and Power

As I mentioned before, do your friend a favor and remind him/her to set aside a budget for an antenna.

If you build your own wire antenna, you can create an amazing one for $50 or so in quality ladder line and wire–at least, that’s about what I put into my sky loop antenna. Retailers like Universal Radio, HRO, and Gigaparts stock quality pre-made wire antennas that cost a bit more, but are pre-tuned, durable and very easy to deploy. The type of antenna you can install is totally dependent on the environment around your home, access to your radio room, and any local interference you might need to mitigate.

Of course, all of the radios mentioned above need a DC power supply. There are many on the market from lightweight switching power supplies to heavy linear supplies.

I would not choose one of the cheapest ones you can find because switching power supplies especially can inject noise. I’m a big fan of the Powerwerx SS-30DV which will typically cost around $110 at ham radio retailers (although, at present, it’s one of the many items out-of-stock due to the Covid-19 pandemic). It hits the sweet spot for me and is a little workhorse!

What do you think?

As I always say: radios are a personal choice. Specifications and features make for convenient points of comparison, but often choices are made based on a user’s own needs and operating style.

Between the Xiegu G90 and Icom IC-7300, which would you choose as a first rig? Can you think of a better compromise?  Please comment!


Do you enjoy the SWLing Post?

Please consider supporting us via Patreon or our Coffee Fund!

Your support makes articles like this one possible. Thank you!

Spread the radio love

How would an Icom IC-705 compare with the Xiegu G90?

Xiegu G90 with remote head detached.

Many thanks to SWLing Post contributor, Paul, who asks:

How does the Icom compare with the Xiegu G90, besides lack of a built-in antenna tuner, and having lower transmit power, and a better screen?

Good question, Paul.

The G90 is a great radio for sure and has better specs and features than I would expect from a $450 transceiver. I’ve taken it on a number of portable field operations and love it. My full review of the G90 will appear in the August 2020 issue of The Spectrum Monitor.

Keep in mind that at time of posting (July 21, 2020) no one has really reviewed and compared the performance of a production run IC-705 with any other radio as of yet. I will purchase an IC-705 for review as soon as they start shipping in the US, but I don’t expect to be able to do that until September or October at best. So we can’t really speak about performance at this point.

What makes the IC-705 unique in the portable radio market is the number of features it will sport.

Here’s a short list of features the Icom IC-705 has that the Xiegu G90 does not have:

  • Attachable battery pack
  • Lower current drain in receive per Icom specifications
  • CW memory keyer with beacon mode
  • Voice memory keyer with beacon mode
  • D-Star mode with built-in WiFi to connect to Internet/hotspot
  • Built-in GPS
  • Built-in TX/RX recording
  • Broader receive range: 0.030–199.999 and 400.000–470.000 MHz
  • Multi-mode 6M/2M/70CM TX and RX
  • Touch screen display that is customizable
  • Built-in WiFi and Bluetooth
  • Native to digital modes–no external sound card interface needed
  • Frequency stability less than 0.5 +/- ppm in VHF/UHF, making it ideal to drive an amplifier for demanding tasks like EME

The Xiegu G90 actually has a few features that the Icom IC-705 will not:

  • Built-in (very effective) automatic antenna tuner
  • Antenna analyzer function [Update: Geoff notes “The Icom IC 705 does also have a VSWR Plot/analyser in the menu same as the IC7300 and iC 7100, page 9.3 in the advanced IC 705 manual”
  • 20 watts of output power (the IC-705 has a max output power of 10 watts using an external 13.8V battery source)
  • 10.8 kHz AM bandwidth (the IC-705 maxes out at 6 kHz per specs)
  • Detachable faceplate which will likely make mounting it mobile even a little easier than the IC-705 (although in truth both transceivers are very compact and should be easy to mount)
  • Side panels that protect the front faceplate and rear connections

At the end of the day, though, the Xiegu G90 is an excellent little budget transceiver. It’s feature-rich compared with other transceivers in this price bracket, but basic compared with the IC-705 or Elecraft KX3 or KX2.

The Icom IC-705 will have a retail cost well over two times that of the G90 but will sport features that no other QRP transceiver has up to this point. In fact, the list of features above is only a sampling.

If none of the unique features of the IC-705 appeal or apply to you and your operating style, save a little money and grab the G90. Or consider spending a bit more for an Elecraft KX2.

If you want an incredibly feature-rich transceiver and are comfortable with a price point in excess of $1100-1200 US (estimated at time of posting), you might delay purchasing until you’ve read a few user reviews of the yet-to-be-released Icom IC-705.

Thanks for your question!


Do you enjoy the SWLing Post?

Please consider supporting us via Patreon or our Coffee Fund!

Your support makes articles like this one possible. Thank you!

Spread the radio love

Upgrade the encoder on your Xiegu G90 for about $8.00 US

Shortly after posting some of my initial impressions of the Xiegu G90, SWLing Post contributor, Guy Atkins, encouraged me to upgrade the stock G90 tuning knob/encoder with one that is highly recommended by the G90 community.

While I didn’t really have an issue with the stock plastic knob, I couldn’t resist a larger, slightly heavier aluminium encoder with a dimple.

The stock G90 encoder knob (before pic)

I’m so happy I splurged for this $8 upgrade. Not only is the encoder much easier to use now, but it also gives the G90 a proper face-lift:

The upgraded aluminium G90 encoder knob (after pic)

Thanks so much for the tip, Guy! I, too, highly recommend this affordable upgrade!

Get your upgraded encoder knob from:

Spread the radio love