Tag Archives: RTL-SDR

A $38.99 RTL-SDR with 100 Khz – 1.7 GHz coverage

Many thanks to SWLing Post contributor, Bill, who recently shared a link to this very affordable RTL-SDR with wideband coverage.

I am not at all familiar with this model, but I do like the enclosure and the fact it has both an HF and UV antenna jack. This must be one of the least expensive SDRs on the market with HF coverage.

Here are a few details per Radioddity.com:

Features:

100% Brand New And High Quality
Using the RTL2832 idle channel, broadband connection impedance isolation transformer provides the signal to the signal receiver HF HF bands.
Increased input low-pass filter to improve noise performance of the machine. At the same time, it retains the original V / UHF band reception, creative use of studded way to achieve RTL2832 + R820t circuit board assembly and connecting circuits increases
Further improve the overall performance of the circuit.
In the homemade circuit board also surrounded, surrounded reserved some help to further develop the pads. The entire circuit is loaded inside a small aluminum to further improve the performance of the overall circuit interference by aluminum shielding.

Package Contents:

1 x 100KHz-1.7GHz full band UV HF RTL-SDR USB Tuner Receiver/ R820T+8232 Ham Radio
1 x USB cable
1 x antenna

Post Readers: If you have experience with this little SDR, please comment!

Spread the radio love

Chris has developed an easy way to run the RTL-SDR dongle on a Mac

5 Replies

Many thanks to Chris Smolinski who writes:

I wanted to run SdrDx, and other SDR apps on my Mac with an RTL SDR Dongle. So I wrote this server app, that makes it appear like a networked SDR.

No need to install any RTL libraries, or compile any code.

Just run the app on your Mac, configure it and your SDR app, and you’re all set.

The app is free, and should work with Mac OS X 10.6 through 10.11.

Chris has kindly allowed me to share his full post here on the SWLing Post below–you can read the original at RadioHobbyist.org:

Running an RTL SDR USB Dongle On Your Mac The Easy Way With Cocoa RTL Server

I’ve had a few of the RTL radio tuner dongles for a while. These are USB devices that were originally made for use as TV tuners overseas, but it turns out that you can access the I/Q data stream, and turn them into an SDR (Software Defined Radio). They can be tuned roughly over a range of 25 to 1700 MHz, and sometimes even higher, depending on the tuner IC chip inside the particular dongle.

I previously posted about how to get the RTL dongle working on the Mac here: An SDR for $17 – The R820T USB RTL-SDR DVB-T Dongle and here: An SDR for $17 – The R820T USB RTL-SDR DVB-T Dongle – Part 2. These posts were from 2013, and I did the installation on a Mac running OS X 10.6, using some pre-built libraries.

Fast forward to the present day. I got a new Mac running OS X 10.11 El Capitan, and I wanted to be able to use the RTL dongles with my favorite SDR software on the Mac,SdrDx. Enter Cocoa RTL Server.

Cocoa RTL Server is a stand alone app that interfaces with an RTL dongle. It does not require you to build or install any drivers or libraries. It just works. It’s based off of an open source app called SoftShell, that I heavily extended. Cocoa RTL Server also acts like a networked SDR, following the RF Space protocol. That means it works with SdrDx, as well as any other SDR app on the Mac that supports RF Space SDRs like the netSDR. You can download a copy of the app from the Cocoa RTL Server page. Source code is included, however I am not offering any support for the project or final app.

Here’s a screenshot of the app running:

Getting up and running is easy:

1. Plug in your RTL device
2. Run CocoaRTLServer 2.0
3. Select the device from the popup menu (usually it is already selected)
4. Change the rtl_tcp or tx_tcp port values if needed
5. Click Open
6. Configure your SDR app (set the correct TCP port) and run it

I’ve run it under Mac OS X 10.6, 10.10 and 10.11, It should run under 10.7-10.9 as well.

Using SdrDx, I can tune a large portion of the FM broadcast band, click to view full size:

In this case I am tuned to 97.9 MHz. To the left of the signal meter, you can see it has decoded the station ID from the RDS data. Yes, SdrDx decodes RDS.

If you look at the lower right corner, you see the scope display of the demodulated FM audio. There are markers for the portions of interest:
You can see the main audio above the green marker to the left.
The stereo pilot at 19 kHz (red marker).
The stereo subcarrier (aquamarine)
The RDS data (orange)
The 67 kHz SCA subcarrier (purple)
The 92 kHz SCA subcarrier (yellow)

Cocoa RTL Server also includes a server that emulates rtl_tcp, so it works withCocoa1090 which decodes aircraft transponders that transmit on 1090 MHz. It should also work with any other app that gets data from rtl_tcp. Here’s a screenshot of Cocoa1090 running:

Thanks so much for developing this app, Chris!

I think I might go ahead and pull the trigger on an RTL-SDR as it would be great to run one on my Mac. I think your app will make the process much easier.

Readers: make sure you check out Chris’ blog RadioHobbyist.org.

Spread the radio love

How to use the SDRPlay RSP as a panadapter

14 Replies

SDPlay-RSP

In this post, I will show you how to use an SDR as a panadapter for a commercial communications receiver. I’m using an Icom R72 and a SDRPlay RSP, but you can do it with nearly all receivers and SDRs.

The Icom R72 is a double conversion HF (0-30 MHz) communications receiver.

A panadapter lets you see the spectrum of your receiver (it gives you a broader, higher-level picture of what’s around your tuned frequency). After using it, you’ll wonder how you’ve been using your receiver without a spectrum display! 🙂

Almost all the radios we use are of superhetrodyne type. To connect a SDR to the radio, you should first find its 1st IF mixer output (if it has more than one Intermediate Frequency stage).

To find it, the best way is to consult the service manual. The first IF of Icom R72 is 70.4500 MHz, so we can use RTL-SDR dongles too.

Here’s a part of R72’s schematics, extracted from its service manual:

IC-R72-Schematic-Mehdi-Asgari

Look at the R82 resistor; it’s located at the output of first IF stage, so I soldered a connector to its pins (its other pin is connected to the ground)

Between the R82 resistor and the output, we’ve added a series 470-ohm resistor (to prevent loading the IF stage)

Click to enlarge.

The other side of this connector is connected to the antenna input of my SDRPlay RSP.

Now I can view my spectrum on a PC.

Here’s a screenshot of CubicSDR on Mac OS X (you can use other apps like HDSDR, SDR Console, etc.):

CubicSDR-Screenshot-Mehdi

Although this post was about the SDRPlay RSP and Icom R72, this procedure can be done for almost any combination of receivers and SDRs provided that your SDR covers the frequency of first IF stage.

Also, don’t forget that you should tune the SDR to the frequency of IF–in this case: 70.4500 MHz.

Mehdi Asgari, the author of this post, is a regular contributor to the SWLing Post. Mehdi lives in Tehran and is an active member of the EP2C amateur radio club.

Spread the radio love

Dr. Phil’s radio articles: portable SDR and pocket DX

5 Replies

SWLing Post reader, Dr. Phil, recently contacted me regarding a collection of articles he’s written about DXing and radio modifications.

His site actually has a number of useful articles that I’ll plan to convert to future posts, with his permission.

I asked Dr. Phil for links to two of his most popular publications. He replied:

My two big recent articles are shown below. One is about “Pocket Radio DX”: using under-$20 radios to DX (started in 2003). Click here to download as a PDF.

The other is about using an $18 NooElec TV-tuner as a MW and shortwave receiver. Click here to download as a PDF.

Brilliant! Thanks so much for sharing these, Dr. Phil!

I actually have a Sony ICF-S10MK2, which I consider to be a capable and useful little AM/FM receiver for the sub $20 price. I’ve also been very tempted to purchase an RTL-SDR dongle, so I may go ahead and bite the bullet on one of the NooElec SDR dongles.

Spread the radio love

Roundup of software defined radios

Excellent website dedicated to the RTL-SDR

Video: Review of the DX Patrol SDR dongle

10 Replies

Many thanks to SWLing Post reader, John, for sharing this video review of the DX Patrol SDR receiver.

The reviewer gives the DX Patrol high marks on shortwave performance, but admits that there is a significant learning curve in terms of software installation and tweaking settings for performance.

At 79 € ($110 US) the DX Patrol is certainly an inexpensive wide band SDR. Unlike the $20 RTL-SDR dongles, the DX PAtrol requires no external up-convertor.

Click here to purchase the DX Patrol online, but keep in mind that the reviewer above noted a 6 week turn-around time for shipment.

If you have experience with the DX Patrol SDR, please comment!

Spread the radio love