Jameco | The SWLing Post

Note that not all power supplies are listed as “regulated linear”

Many thanks to SWLing Post contributor, Dave Zantow (N9EWO), who replies to a post published yesterday regarding some of Jameco linear power supplies. Dave writes:

“A bit of a caveat on Jameco’s these so called Linear power supplies. This is based from my own experiences so is not fiction.

Bottom of this page : http://www.jameco.com/Jameco/catalogs/c151/P92.pdf

Over the years some of (but not all) these Jameco linear regulated power supplies are no longer clean for radio use.

Without changing the model number or description of the product, they have made changes with some (or much of ??) this “Linear Regulated” adapter line. Indeed they are still using a good old power transformer, but when it comes to the regulator part of the adapter, they have gone to switching type regulator device. So it produces a nice strong whine on a radio receiver just as a full fledged switching supply.

I had purchased a number of these so called linear supplies (sorry I no longer have the exact model number noted that I ordered) and experienced awful interference with any radio receiver. So I cracked open one of these to see what was up here and sure enough it was using a MC34063A inverting switching regulator .

Called Jameco and they flat out denied that they were using any switching devices in this Regulated LINEAR Jameco ReliaPro adapter. So I then sent a nasty gram email to the CEO of Jameco. I received an email back (was from the CEO too) and after some research they FINALLY did admit a change was made in some of the product line to use of a switching regulator . But he strongly made the point they would continue to still market these adapters as totally linear (yeah right ….nice guys).

I must add here that it does (or did not) NOT affect the entire line of these linear regulated adapters. About a year ago I ordered more (already had a few before) of the 12 volt 1 AMP model 170245 , and these are (or were anyway) totally clean and are excellent.

Also note that Jameco purchases up surplus “linear regulated” adapters from time to time. This 6 volt 500 ma one here is an example and is (or was anyway) nice clean one and uses no switching regulators. Our 2 tested samples of this adapter from about 5 years ago used a nice 7806 analog regulator. Perfect for use with many SW portables, (including the Sony ICF-SW7600GR with a plug change). But a warning again from experience , they are all subject to changes without any warning (and this one may have changed too for all we know ??)

They appear to stick the ReliaPro name as the manufacture on all adapters (if it was made by Jameco or not)

So Caveat Emptor.”

Duly noted, Dave! I’ve also noted that not all of the power supplies on their linear power supply page are listed as being a linear supply (see screen grab at top of page).

I may contact Jameco about this too and see if they can adjust their search results to properly reflect a selection of regulated linear supplies.

Spread the radio love

Regarding noisy switching power supplies, SWLing Post reader, Dan Lewis, comments:

“Google the following: “Jameco linear wall transformer”, and you’ll find a suitable non-switching replacement.

Jameco still has a number of linear transformers in their catalog at reasonable prices. I haven’t bought anything from them in many years but when I dealt with them frequently a number of years back they were always reputable.”

Many thanks for your suggestion, Dan! Jameco is a reliable company and I’ve also been a long-time customer. If you know how to pick the proper power supply for your radio (or any other electronic device) click here to view a list of regulated linear supplies on Jameco’s website. [Also note this follow-up post.]Otherwise, keep reading…

How to find a replacement AC adapter/power supply

When you purchase a replacement power supply, you must make sure that several properties match that of the device it will power, else you could cause damage.

There are four properties you need to match: voltage, rated current, polarity and tip size.

Voltage

Most consumer electronics are powered by and rated for 4.5, 5, 9, 12, or 13.8 volts DC. Of course, there are exceptions. It is important that you match the required voltage exactly. Most radios and electronic devices display their required voltage and voltage tolerance on the unit itself, on the supplied switching power supply, and/or in the owner’s manual.

Rated Current

Like voltage, rated current is usually displayed somewhere on the device, existing power supply or in the owner’s manual. Current is usually indicated in amps (A) or milliamps (mA). Unlike voltage, rated current on your power supply does not have to match the device exactly. You simply need to make sure the power supply meets or exceeds your radio’s required current.

For example, if your radio requires 800 mA (or .8 A) and you find a power supply rated for 500 mA, you should not use it. If you find a power supply rated for 2 amps (or 2000 mA), it exceeds the 800 mA rating, so you’re good to go!

Unlike voltage, your electronic device or radio will only draw the amount of current it needs from the power supply.

Polarity

Click here to read more about tip polarity. (Source: WikiPedia)

You’ll need to determine if your radio requires a plug with a positive or negative tip (a.k.a. center conductor).

Fortunately, manufacturers have long used standard symbols to make polarity obvious (see image).

You’ll typically find a polarity symbol printed on the back of your radio, near the plug-in point, in the owner’s manual or on the back of the existing wall adapter.

Note: Be very careful matching polarity! Some radios and electronic devices are not properly protected against reverse polarity; damaged can occur immediately after supplying voltage with incorrect polarity.

Tip/plug size

You need to make sure that the inner diameter and outer diameter of a replacement wall adapter will match that of your existing adapter.

This can be the most difficult property to match.

Occasionally, radio manufacturers will actually specify the tip size in their owner’s manual, spec sheets, or on the product page of their website. I’ve even had luck calling manufacturers and asking a technician for the plug size.

Specification sheets will typically indicate plug dimensions with an illustration.

Otherwise, you can always measure the existing power supply tip (both inner and outer dimensions) using calipers.

Once you have those dimensions, finding the appropriate replacement power supply is quite easy. Indeed, companies like Jameco provide specification sheets (click here for an example) that indicate dimensions for each power supply they sell.

Once you’ve matched the voltage, rated current, polarity and tip size, you can purchase a regulated linear power supply with confidence!

Keep in mind: there are most likely other devices in your home with noisy switching power supplies that could be causing radio interference. Check out my noise trouble shooting section of this article to help identify local sources of radio noise.

Update: check out this follow-up post regarding Jameco power supplies–not all are truly linear regulated.

Spread the radio love