Tag Archives: Elecraft KX2

A quick recap of yesterday’s Carl Sandburg Home NPOTA activation

img_20160908_172739245_hdr

Yesterday, I fit in yet another activation of the Carl Sandburg Home (NS01) for the ARRL National Parks on the Air. You might recall, I activated the same site last Sunday.

The lake at the trail head.

The lake at the trail head.

Second time’s a charm!

Since I had already scoped out the site and the trail where I operated last time, I took a minimum of supplies: My Elecraft KX2, EFT Trail-Friendly antenna and the accessories in my go kit:

LowePro CS 60 Closed

I didn’t even need a folding chair as I hiked further into the trail system and found a bench in an ideal shady location where I could hang the EFT antenna without any part of the wire being close to the trail itself.

The only negative was that I had to fight off a few mosquitoes–par for the course!

img_20160908_163154954_hdr

After firing up the KX2, I found that both frequencies I announced (14,286 and 7,286 kHz) were occupied. I tuned around and found clear frequencies then posted the changes on Twitter and the ARRL NPOTA Facebook page. Fortunately, I was spotted on the DX clusters after my first contacts (thanks, Mike and others!).

In short: this was about the busiest I’ve ever been on the radio.

In 43 minutes, I logged 41 stations: many stations here in the southeast US, and stations from New Mexico to Italy! Propagation and timing were certainly in my favor.

The rubber band held my KX2 to the clipboard, but I hope to sort out an even better way of securing it.

This red rubber band held my KX2 to the clipboard, but I hope to sort out an even better way of securing it in the future.

The pileups were heavy enough that I didn’t even have time to properly pull log sheets once I had completed them–instead, I folded them over the KX2 and continued writing.

I was very pleased that I logged at least one SWLing Post reader: Randy (KS4L). Thanks for the contact, Randy!

Not all portable operations go so well…but when they do, it’s energizing!

I might be able to squeeze in a 30 minute activation on the Blue Ridge Parkway (PK01) this afternoon.  Listen for me (K4SWL) around 14,286 kHz SSB sometime between 20:30-21:30 UTC. That is, if propagation and my schedule cooperate again!

Spread the radio love

NPOTA: Activating the Carl Sandburg Home (NS07) today

Elecraft Kx2 ON Clipboard

This afternoon (September 8), I should have a chance to activate the Carl Sandburg Home again for the ARRL National Parks on the Air program. You might recall, I activated the site Sunday as well.

I’ll plan to use the Elecraft KX2 and EFT TRail-Friendly antenna combo once again.

I should be on the air starting sometime between 20:00-20:30 UTC (4:00 – 4:30 PM EDT). I’ll plan to operate SSB on two frequencies: 14286 and 7286 kHz. I should be on the air for one hour or so, if all goes well. Listen for my amateur radio call sign: K4SWL.

It would be fantastic to log some SWLing Post readers. If you do manage to hear my 10 watt signal, or work my station, please comment!

Spread the radio love

Labor Day Fun: A hamfest, an NPOTA activation–and a new Elecraft KX2 QRP kit

NS07-Carl-Sandburg-Home

My station location on the trail near the Sandburg farm is indicated with the small grey marker (lower left quadrant).

I’ve enjoyed an especially “radio-active” Labor Day weekend.  Here’s hoping you did, too.

On Saturday I headed out the door at 4:15 AM to meet my buddy Vlado (N3CZ), the inimitable radio doctor; we aimed our headlights through the morning mist to the Shelby Hamfest. Though it took quite a bit more coffee to keep me going, the hamfest was a load of fun. Check out the photos I posted yesterday.

ARRL-NPOTAOn Sunday, I enjoyed some family time. Conveniently, our weekend travel took us near the Carl Sandburg Home in East Flat Rock, NC.  I managed to carve out a little time for a quick–very quick– NPOTA activation of the site.

I realized I would only have about an hour, though, to find a suitable site, setup my radio kit, make at least the minimum of ten contacts, then pack up and clear out.  Not an optimal amount of time, but certainly a fun challenge.

This was also a good excuse to try out my new Elecraft KX2 portable transceiver kit in the field. I haven’t even had the KX2 for a full week, but I quickly put together a field kit with the Elecraft as a centerpiece.  If you’re curious, the kit consists of the following:

  • The Elecraft KX2, with internal battery and ATU options
  • An LnR Precision EFT Trail-Friendly antenna (purchased at the Dayton Hamvention)
  • An assortment of connectors and adapters
  • A six-foot coax cable
  • An Elecraft hand mic, borrowed from my KX3
  • A CW paddle (the KXPD2)
  • A clipboard, log sheets, and mechanical pencil
  • Fishing line and a weight (to hang the antenna)

All of this, save the fishing line and weight, was protected by the compact and perfectly portable LowePro ViewPoint CS 60 padded case, and fit it like a glove.

LowePro CS 60 Closed

Let’s talk packs…

Those of you who know me, know that I’m a bit of a pack junkie.  So I’m kind of picky about what I choose to hold my gear. There are a few manufacturers whose packs pass the test, and that make gear here in the States, like Spec-Ops Brand, Red Oxx, and Tom Bihn. Their packs are sometimes pricey, but they’re nearly bullet-proof and guaranteed for life.  Timbuk2, based in San Francisco, is a more economical company with good gear, as well.

After purchasing my KX2, I searched but couldn’t find a suitable pack from my prefered manufacturers. I had remembered that at the Dayton Hamvention, Elecraft was actually selling two models of a LowePro pack that fit the KX2 exactly: the ViewPoint CS 40 and CS 60.

While I like to go as compact as possible, the CS 40 is just  a bit too small to hold everything I like to carry to the field (antenna, paddle, and mic). The CS 60, on the other hand, could hold everything and has a fold out panel organizer to hold connectors.

I knew the CS 60 would fit the KX2, and I knew the CS 60 was padded to protect its contents.  I also could see that the pack has excellent (and apparently genuine) ratings on Amazon, so I ordered one.

I’m pleased to report that the CS 60 is very well built indeed, and what’s more, accommodates everything I need. In fact, the only thing the CS 60 won’t hold is my reel of fishing line and 6′ coax cable (and yes, I daresay you could adapt both items to make them fit with a little effort).

I carried the CS 60 and reel in my trusty 20-year-old Dana Design lumbar pack:

Dana-Design-Pack

There was room to spare inside for water bottle and snacks, and the whole package was very lightweight.

The Carl Sandburg Home

Carl-Sandburg-NS07

The Carl Sandburg site was fairly teeming with visitors, also enjoying the warm weather of the Labor Day weekend. After arriving and (fortunately) finding a parking spot, I hiked 20 minutes to one of the trails, where I was given permission to hang an antenna and operate.

Knowing that I needed to rejoin my family soon, I wasn’t too choosy about my site this time. I just needed to get on the air and work the minimum of ten contacts. In truth, I wasn’t sure if all of this was possible in the one hour I had available.

I setup on the right side of this trail, near one of the park benches.

I setup on the right side of this sunlit trail, near one of the park benches. It turned out to be a pretty good spot.

It took me perhaps ten minutes to set up, with a few brief asides to explain what I was doing to passing hikers.

Since I configured my little Elecraft KX2 with an internal battery and antenna tuner, I had no need for extra power cables, connectors, ATU and coax.

Elecraft-KX2-Clipboard-NPOTA

Yep, my entire station easily fit on the clipboard I was using to hold my log sheets. On my lap, the clipboard became my operating table.

As soon as I sat down in my folding chair, I turned on the KX2, set the frequency to 14,286 kHz, and pressed the ATU button which gave me a 1:1 match (since the EFT is resonant).

Thank you, voice keyer!

Next, I recorded my CQ call into the KX2’s built-in voice keyer by:

  1. pressing and holding the MSG button,
  2. assigning the voice message to “memory allocation 1” by pressing the PRE (1) button,
  3. pressing XMIT to start the recording,
  4. reading off my CQ call “CQ, CQ, CQ, this is K4SWL calling CQ for National Parks on the Air…”, and
  5. pressing XMIT again to stop the recording.

Then I started calling CQ by simply pressing the MSG button and selecting my message stored in memory allocation 1 by pressing and holding the PRE (1) button.

By pressing and holding the PRE (1) button, I initiated a loop-playback of my CQ call where my KX2 would transmit my call from memory.  Then I waited a few seconds to listen for any replies, and played it again. (In loop-playback mode, the KX2 will repeat my CQ call until I interrupt it by pressing a button or keying my mic.)

It’s a brilliant and easy function which saves my voice! By automatically calling CQ, it  gives me an opportunity to answer questions from curious passersby,  naturally fascinated by a guy sitting on the side of a trail, talking into a little box connected to a tree-branch suspended wire.

In the end, I didn’t even need to use the voice keyer that much. I was spotted on the DX cluster and within moments had a small pile-up of stations. Remarkably, I worked my minimum of ten stations within six minutes! Of course, I continued to call CQ until I worked everyone in the pile-up (including stations from California, Nebraska, Kansas, Texas and Mexico). Though I was running out of time quickly, I did switch to the less-active 40 meter band and called CQ. In a period of a few minutes, I worked two stations on forty: one from Alabama and one from Florida. Not bad for 10 watts of power!

Elecraft Kx2 ON Clipboard

Packing up

Normally I would have stayed on the air for at least an hour to give chasers an opportunity to work my station, but I was pleased that I’d managed to fit this activation into a very busy schedule. I was glad to have racked up so many stations, so quickly!

Taking down the antenna and packing up my portable station took all of eight minutes.

Without a doubt–once I had hiked to my operating site–this was my fastest deployment, activation, and pack-up to date. It was all possible because:

  1. the KX2 has a built-in battery pack and ATU, and is so small it fits on my clipboard,
  2. the EFT Trail-Friendly antenna is a breeze to install, take down and pack, and
  3. the CS 60 pack organizes the radio and accessories so handily.

LowePro-CS-60-Open

In short: I’m totally pumped by my new QRP field kit!

More radio adventures await…To the field!

Spread the radio love

AM Mode: Comparing the Elecraft KX2 with the LNR Precision LD-11

My new Elecraft KX2 tuned to Radio Australia this morning.

My new Elecraft KX2 tuned to Radio Australia this morning.

I’ve only had my Elecraft KX2 since Monday evening and have been so busy, I’ve only had an hour or so to tinker with this pocket transceiver. Monday evening, before putting it on the air, I updated the KX2 firmware to the latest Beta release which includes the new AM mode.

I’ve had so many questions from readers about the KX2’s AM audio already, I thought I’d do a quick comparison with the LNR Precision LD-11.

I set the LD-11 to a bandwidth of 9.6 kHz, and the KX2 to 5 kHz: their widest AM filter settings. Keep in mind, this is not an apples-to-apples comparison, but it does showcase each radio’s potential AM audio fidelity.

I tuned both rigs to the Voice of Greece last night on 9420 kHz around 00:30 UTC. VOG’s signal was strong into North America.

I made the following recordings with my Zoom H2N digital recorder, by feeding in-line audio patched from each radio’s headphone jack. I tried to balance the audio levels between the two rigs.

Here are the results:

The LNR Precision LD-11

LNR-Precision-LD-11-AM-Mode-Voice-Of-Greece

Click here to download the audio.

The Elecraft KX2

Elecraft-KX2-Voice-Of-Greece-AM-Mode

Click here to download the audio.

The Elecraft KX2 in “Delay” audio mode

Note: Some Elecraft radios have an audio effects mode which includes a “delay” function. Elecraft describes it as “a quasi-stereo effect intended to provide depth and space to the received audio.” On an AM broadcast signal, it makes it sound wider and gives it almost a stereo depth.

Elecraft-KX2-Delay-Audio-AM-Mode

Click here to download the audio.

I think the results from both radios are impressive. Since the LD-11’s bandwidth can be widened to 9.6 kHz, strong signals like this one sound pretty amazing. In truth, I actually prefer a filter width of about 8.2 kHz on strong signals, but VOG was wide enough to justify 9.6 kHz.  I believe the LD-11 would rival many dedicated tabletop receivers.

The Elecraft KX2, in normal audio mode, sounds flatter and narrower than the LD-11 of course, but still very pleasant!  In the KX2’s “delay” audio mode, the signal sounds much wider than 5 kHz, though the effect adds a little graininess to the audio. That’s okay, though–I love having the “delay” audio option in my tool bag.

Here’s what amazes me as an SWL and ham radio operator: both of these QRP transceivers offer excellent HF broadcast listening opportunities.

Please comment! Which audio sample do you prefer? Do you like the “delay” audio effect on the KX2? Keep in mind this is only one comparison and doesn’t address sensitivity or selectivity.

Spread the radio love

John takes the Elecraft KX2 on the shortwaves

ElecraftKX2

I just noticed that John (AE5X) has updated the firmware on his KX2 and made a short video of a shortwave band scan. On his blog, he notes:

Before getting my ham ticket, I was a SWL and am very happy that AM capability has been added to the KX2, making a fantastic radio even better.

[…]We have a very powerful AM broadcast station near my QTH on 740 kHz. I was not able to receive it at all with the KX2. Unlike some, I see this as beneficial – it tells me the 80m filters (the KX2 doesn’t operate on 160m) are doing what they were designed to do.[…]

Read the full post on John’s excellent blog.

Click here to view John’s video on YouTube.

Update: I’ve had my KX2 for 24 hours now! I’ve already updated the firmware and will post a couple AM audio samples soon.

Spread the radio love

Video: Elecraft KX2 daytime shortwave AM performance

ElecraftKX2

After publishing the post this morning regarding the AM mode addition to the Elecraft KX2, SWLing Post contributor Ivan Cholakov (NO2CW) created the following video comparing the KX2’s daytime shortwave reception with that of the Kenwood R-2000:

Click here to view on YouTube.

Spread the radio love

The Elecraft KX2 now has AM mode!

Elecraft-KX2-6

The Elecraft KX2 at the 2016 Hamvention

Many thanks to a number of SWLing Post readers (including, Eric, Dave, Jim and Greg) who shared the following message from Wayne (N6KR) on the Elecraft message boards:

We added AM mode to the KX2 today, both transmit and receive. Its primary purpose is for SWL (short-wave listening), i.e. copying commercial AM stations. (Remember that the KX2’s sensitivity drops off rapidly below 2 MHz due to protective high-pass filtering, so it wouldn’t be your first choice for AM brodcast-band DXing.)

AM transmit is far less efficient than SSB, so it would typically be used only if the target receiver can’t demodulate SSB, or for special applications. For example, there’s some AM activity and experimentation in the ham bands, notably around 3.870 kHz at night. I’ll have to drop in with 10 watts (carrier + sidebands) and get a report 🙂

While the KX2 was optimized for SSB, AM mode sounds fine, and of course is easier to tune than when using SSB modes with AM. In AM mode, the operator can select 1, 5, 9, or 10 kHz steps for course tuning using the VFO CRS menu entry. (Yes, some countries use 9 kHz intervals between stations.)

If you’re interested in testing AM mode on the KX2, please email me directly.

73,
Wayne
N6KR

On Sunday, I ordered a KX2 (with ATU, rechargeable battery pack, quick charger and paddles)–it should arrive next Monday. First thing I’ll do is upgrade the firmware so it’ll have AM mode.

Many thanks to Wayne (N6KR) for putting this KX2 upgrade at the front of the (long) line of requests.  I’ll be reviewing the KX2 for the November issue of The Spectrum Monitor magazine and, as an avid SWL, AM mode adds an important dimension to my evaluation. (Truth is, I know that Wayne has a soft spot for SWLing too.)

Elecraft-KX2-Data-SheetClick here for a previous post with more information and photos of the Elecraft KX2.

Click here to view the KX2 on Elecraft’s website.

Spread the radio love