Tag Archives: Yaesu FT-891

Guest Post: Mark’s review of the Yaesu FT-891 as shortwave broadcast receiver

Many thanks to SWLing Post contributor, Mark Hirst, who shares the following guest post:

Using the Yaesu FT-891 for SWLing

by Mark Hirst

Woodland Operation in North Hampshire

Introduction

While I have a small collection of portable shortwave radios for outdoor listening, I’ve been looking to fill a gap in my amateur radio lineup for a while. Outdoor operation has become important in recent years as solar cycle conditions deteriorated along with rising levels of QRM in urban neighbourhoods. The ICOM IC–7200 with Wellbrook loop stays at home fighting a losing battle with PLA noise, while the very portable FT–817ND does occasional data modes contacts and outdoor listening. Somewhere in the middle, the FT–891 promised to provide a modern and more powerful data modes station, a radio to take on holidays, needing external batteries, but portable enough for walks into the country side. Earlier this year, I bought one new from my local ham radio store, and what follows are my findings and observations so far on shortwave listening.

Audio Characteristics

I’ve accumulated hundreds of recordings of VOA Radiogram and Shortwave Radiogram since 2013, so a recent woodland expedition with the FT–891 was an opportunity to compare a recording made with it against those of other radios I’ve used.

The most striking difference is the lack of frequencies in the lower part of the audio spectrum along with a distinct cut off at around 5kHz.

This is easily visualised in the following comparison between the FT–891 and the Tecsun PL–680. Note the conspicuous pillar associated with MFSK32 from these Shortwave Radiogram broadcasts, and interfering RTTY on the FT–891 recording:

Audio Frequency Analysis

While this audio profile may not be to everyone’s taste, the extra sparkle yields voice audio that is clear and distinct. I find those low frequencies make the audio muddy and tiring to listen over long periods, so I’m quite happy with this.

When listening to speech based broadcasts through the top mounted speaker, the audio is also precise and intelligible, and provides more than enough volume.

You can judge for yourself from this 2 minute video I made recently:

Headphones, External Speakers and Recording

You also have the option of connecting an external speaker or headphones to a socket on the side of the radio. Be aware that the audio level is different for headphones, and is controlled by a small switch hidden behind the front panel. I expect people may go for one option such as headphones and then stick with it, rather than continually detaching the front of the radio and moving the delicate switch back and forth.

If you turn the volume right down you will hear a hiss, although its really only noticeable if you face the speaker directly and get close. Listening outdoors with the sounds of nature around you? It’ll be fine. There’s no way to avoid it with headphones of course, with forums suggesting inline resistors or high impedance headphones as solutions.

Audio recordings can of course be taken from the headphone socket, but you will get better results from the data port on the back. I use a UD04YA cable which provides 3.5mm audio in and audio out jacks, plus a USB cable to provide PTT functionality. It’s meant for data modes operation with the FT–817, but I have used it successfully with the FT–891 for PSK contacts using fldigi, eliminating the need for CAT control through a second cable to the radio’s USB port.

Customising for SWL

The advanced manual for the FT–891 helpfully provides a section called ‘Tools for Comfortable and Effective Reception’, so I began configuring the radio using the guidance there.

First up was re-configuring the front panel RF/Squelch knob to only control RF gain (Menu 05–05). I use the same configuration on my FT–817ND to dial back RF gain, allowing the AGC to pick up the slack.

Next was enabling the awkwardly named Insertion Point Optimisation (IPO) which switches out the pre-amplifier. It’s interesting to note that this setting can be associated with a stored memory channel, which became relevant later when I used CAT control to program some favourite frequencies.

The radio has an attenuator, although I’ve not found a need for it so far.

The AGC can be configured as Auto, Fast, Mid, and Slow. Since it is not a ‘set and forget’ setting like the RF control or IPO options, it might be a good candidate for assigning to one of the three user definable buttons below the LCD screen.

Audio can be fine tuned using four menu options (06–01 to 06–04) to control high and low frequency cutoff, but after some experimentation I have turned these options off.

As an aside, I found the LCD backlight, button illumination and TX/Busy lights too bright for indoor use, so dialed them back to their minimum values.

Listening Tools

The radio provides some additional tools as part of its IF DSP. The features of particular interest are Digital Noise Reduction (DNR), Noise Blanker, IF Notch Filter, Digital Notch Filter, and Narrow IF filter. Contour, IF Bandwidth, and IF Shift are not available in AM mode, and you must resort to SSB to get them. More about SSB in a moment.

Out of this wide array of options, I’ve only explored Digital Noise Reduction and the Narrow IF filter so far, as they offer fairly immediate gains without too much configuration.

Narrow filter simply reduces the total IF bandwidth from 9kHz to 6kHz, which gives some immediate relief to higher frequency noise. In tougher conditions at home tackling QRM, the harsher sound it causes has sometimes been counter productive.

At the outset, it’s obvious that the DNR capability of the FT–891 is a powerful feature. Rather than providing a level of processing that varies from a little to a lot, the radio provides 15 different ‘algorithms’ which can be selected for best results. This means you will tweak the DNR setting to address signals on a case by case basis.

Comparing it with the IF noise reduction of my ICOM IC–7200, the ICOM has a scale of diminishing returns as the DSP level is turned up, whereas the FT–891 seems to start strong and it’s more about picking the algorithm that sounds best.

After testing the DNR on AM broadcast stations away from the noise at home, voice audio sounds distant and words can be clipped, which is fine for SSB amateur radio contacts, but makes me think it’s not a feature of first resort when trying to improve broadcast reception. In those circumstances, the narrow filter might be a better option.

The Trials of Single Side Band

On the matter of SSB and using it to combat adjacent or co-channel signals, the radio offers a single SSB option in the mode menu, picking USB or LSB for you automatically based on the current band. When tackling broadcast band interference however, you want the option to go in either direction. The radio also changes the current frequency by 700Hz when SSB is selected, which then has to be corrected with the main dial.

You would begin by switching to SSB mode by pressing and holding the band button. If you’re lucky, the default setting is the one you want.

If it isn’t, activate the settings menu with a long press of the F key, go to the menu option SSB BFO (11–07), select it and use the multi-function knob to change the mode away from Auto to LSB or USB.

As you are doing this, the VFO will change to LSB or USB too. Leave the setting on the option that suits your needs.

If you exit the menu option without saving (pressing F), the mode will remain changed, but the override is not saved. This can be a useful quirk because next time you turn the radio on, it will be back in auto mode.

If you commit the override by pushing the multi-function knob instead, the radio will stay in manual mode until you remember to return to the menu and restore automatic behaviour again.

It’s a needlessly complicated system, as I discovered recently while recording another Shortwave Radiogram broadcast. Even after testing the procedure previously for this article, the radio was determined to stay in LSB no matter what.

Memory Programming

Since the radio has no keyboard for direct frequency input, an early priority for shortwave listening was to program some of the 99 memories available. My plan was to have some favourite broadcast stations, along with WX, Volmet, GMDSS, and some data mode frequencies. To handle ad-hoc stations however, I wanted a way of moving quickly across the main shortwave bands without excessive use of the main tuning dial or multi-function knob.

Taking the official definitions of the broadcast bands between 60m and 16m, and combining those with frequency schedules, I came up with a series of frequencies 150kHz apart across each of those bands, guaranteeing that no broadcast was more than 150kHz away.

The combined list of favourites and the 150kHz stepping stone frequencies resulted in 70 memory channels in total. As I wanted to apply alphanumeric tags to those channels, and didn’t relish the prospect of entering them manually, my next port of call was the CAT control manual to see how those memories could be set programmatically.

While there is commercial software available for the FT–891, I only needed to set up the memory channels, so decided to adapt some PowerShell I’d written for another radio, sending the necessary serial port commands to configure my list.

Now that is done, I can fast travel using the stepping stone memories to the closest point in a band, then use the fast mode of the main tuning dial to move quickly to my final destination.

The following table lists my current stepping stone channels in kHz:

60m	49m	41m	31m	25m	22m	19m	16m
4750	5900	7200	9400	11600	13570	15100	17480
4900	6050	7350	9550	11750	13720	15250	17630
5050	6200	7500	9700	11900	13870	15400	17780
		7650	9850	12050		15550	17930
		7800				15700

Memory Access

An obvious way to access the memories is to toggle memory channel mode with the V/M button, then cycle through the memories using the multi-function knob. Depending on your memory choices, you will hear relays clicking as the radio jumps back and forth between widely spaced frequencies and bands. You will also need a good memory of your memories, so you know which way to turn the multi-function knob.

An alternative and perhaps faster method is to press the M>V button. This brings up a multi-line listing of memories that can be scrolled through using the multi-function knob. Pressing the M>V button again copies the selected memory to the VFO and leaves you in VFO mode. This avoids the radio flipping across bands and the associated relay activity.

Although it is not documented, if you push the multi-function knob on a selected memory channel in the multi-line listing rather than using the M>V button, the selected memory is activated and the radio is left in memory channel mode displaying the memory tag.

Disabling Transmit

At the time of writing, I haven’t discovered a way of formally disabling transmit, and the minimum transmit power goes no lower than 5W. Since my main interests are around shortwave listening, utility stations and an occasional data mode QSO, I have not fitted the microphone to the radio. In that configuration at least, there is no danger of me manually transmitting into a receive antenna by accident.

Outdoor Power

Reports vary on the power consumption of the FT–891. It certainly isn’t as high as the 2.0A documented in the user guide.

While some sources claim values in the region of 1.0A, my power supply shows around 0.4A at 13.8V when receiving a typical HF broadcast. You will notice where some of that power goes quite quickly, as part of the radio gets warmer.

To save weight, my preferred power supply in the field is usually a lithium battery designed to jump start smaller engined cars. This versatile 12V battery also supplies 5V USB power to phones and tablets, and can even charge laptops.

In Conclusion

Control ergonomics and screen size are factors that can detract from shortwave listening on these kinds of radios, with smaller speakers and menu options for features normally at your fingertips.

Despite this, I’m happy with the audio, and I like the emphasis on mid-range frequencies in its audio spectrum. The digital noise reduction is impressive and can tackle significant QRM environments, but for outdoor listening may not be your first port of call.

Memory presets can make tuning less laborious, while assigning key listening tools to the customisable front panel buttons should reduce the need to access menus. I may consider defining some stations with known co-channel issues to memory with preset LSB and USB variations, to allow rapid responses to interference in future.

In good conditions, I suspect there is little difference between the FT–891 and FT–817ND for general listening. The FT–817ND has produced some of my best recordings of Shortwave Radiogram. The newer radio however brings many advanced tools to bear on more difficult signals, while its band scope and full sized VFO tuning dial enable desktop style shortwave exploration.

The ICOM IC–7200 is constrained by interference at home, biding its time for when the solar cycle swings back. When it’s been out on field days, it has always been a strong performer for broadcast listening. All the important controls are upfront, but is not a trivial thing to transport on foot. While the FT–891 has impressive DNR chops, I think I prefer the ability of the IC–7200 to apply noise reduction in incremental steps. Perhaps the algorithm approach will grow on me in time.

Any amateur radio operator using the FT–891 should have no trouble using it for shortwave listening. It attracts a lot of positive reviews for its ham radio capabilities, and it looks like those features carry across for listening to the world too.

An excellent review, Mark! Thank you for sharing.

The Yaesu FT-891 must be the most popular HF transceivers Yaesu sells today. So many of its users rave about its performance and audio characteristics. Mark, thank you for sharing your experience with the FT-891 as an SWL!

Click here to check out the affordable IP67 rated case Mark uses to house his FT-891.

Spread the radio love

Mark finds an affordable IP67 rated protective case for the Yaesu FT-891

8 Replies

Many thanks to SWLing Post contributor, Mark Hirst, who writes:

Thomas,

I got a new FT-891 recently and wanted a protective case for taking it out into the field.

A mixture of internet searches and Amazon algorithms turned up this very affordable case which closely matches the size of the radio, as the enclosed photograph shows.

It uses the familiar pick and pluck foam, although in two layers.

The base layer is a bit thin, so I might put a layer of rigid plastic over it to stop the feet of the radio pushing down to the outer case.

I prioritised the side wall thickness opposite from the carry handle, as the case is designed to sit on its side like a briefcase.

Via Amazon USA ($29.31)

Via Amazon UK (£20.99)

Mark

Wow, Mark! I do love the size of this case and the fact that it fits the FT-891 so perfectly.

Recently, I’ve been thinking about building out a case to hold one of my smaller QRP transceivers (the KX1, KX2, or MTR3B) in the field to be used when it’s raining. Perhaps this has been on my mind because I’ve been enjoying nearly 5 straight days of rain and fog! A case like this would be an affordable solution and I wouldn’t feel terribly bad about drilling through the case to mount antenna, key, mic, and headphone ports.

I, for one, would love your thoughts about the Yaesu FT-891 as well. I’ve contemplated reviewing it this year mainly because so many field operators rave about it. I’d be curious what you think about it in terms of shortwave radio listening.

Thank you again for the tip!

Note that the Amazon affiliate links above support the SWLing Post at no cost to you. If you’d rather not use these links, simply search Amazon for “Max MAX004S.” Thank you!

Spread the radio love

Using the new Xiegu GSOC and G90 transceiver combo for shortwave broadcast listening–?

9 Replies

Listening to Radio Prague via WRMI with the Xiegu GSOC

Many thanks to SWLing Post contributor, Tim R, who writes:

Dear Thomas,

First of all thank you so much for the all of the energy you put into the SWLing Post. When crazy things are happening in the world it’s a very welcome sanctuary! Sending you some coffee money.

I plan to become a ham radio operator next year. Bought the book last week and once I finish a large project for work, I’m on it. Of course, the Tech license will only give me limited exposure to HF, but I’m already plotting an HF radio purchase because I can’t WAIT do do some SWLing with it. Up to this point, I’ve only owned portable radios and never really have used external antennas other than some cheap wire.

My question…

I’ve been considering grabbing a Xiegu G90 because it seems to be a nice comprehensive beginner’s HF rig and is very affordable. I read your review and understand your caveat that there’s no way to completely disengage the transmit so that it can’t be accidently hit if connected to an RX only antenna. I’m not worried about that because I’m going to hang a G5RV wire antenna and use it both for TX and RX. No problem if RF is accidently sent through it.

Of course, there’s a lot of buzz in the Xiegu community about the new GSOC controller. I had not planned to exceed $600 for my radio purchase, but I love the idea of the controller. But when I add $550 for the controller and $450 for the radio, all the sudden I’m at $1,000.

After some deep soul-searching (and let’s be frank here, a blessing from my wife and CFO) I’ve decided to raise my budget to $1,000.

All of this to ask, if you had $1,000, would you buy the G90 and GSOC controller, or would you get something else keeping in mind I want to use this as much for shortwave listening as for future ham radio work?

Any advice would be appreciated.

-Tim

Thanks for your question, Tim! And thanks for giving me a complete picture of your budget/radio requirements and the antenna you plan to use.

I’ll try to answer your question here, but understand this is more what I would do if I were in your shoes. This is a pretty simple question, but not simple to answer because there are so many options on the market.

Xiegu GSOC and G90 combo option

Keeping in mind, I feel like the GSOC is a work in progress at the moment and not fully developed–check out my initial review. Once the next firmware update is available it could certainly solve a number of small issues I found with the unit. It works, but it’s not a refined product yet.

It’s ironic, actually. When I received your message this morning, Tim, I was SWLing with the GSOC and G90–listening to Radio Prague on WRMI. In the end, though, the GSOC is primarily an enhanced interface for the G90. While it does add some extra functionality (and should, over time, add much more) it doesn’t really change the performance characteristics of the G90. I’d check out my G90 review for more info about performance.

Would I purchase the G90/GSOC combo if I were in your shoes? Again, it’s early days, so I don’t feel comfortable making a recommendation call yet. The G90 is, without question, a great value at $450 (often even less) investment. I like it primarily as a field radio, though, and once you add the GSOC to the mix, it’s a little less portable because it’s two units with quite a few interconnect cables. Of course, you can swap the GSOC unit for the G90 control head at any time, but that involves attaching and re-attaching the control head each time (there’s no accessible serial port on the back of the G90, for example)

If you’re a huge fan of the G90, the GSOC should eventually be a worthy addition. At present, for your use as a new ham and for SWLing, I’d perhaps consider other options too.

The Icom IC-7300

The Icom IC-7300 SDR transceiver

Since you’ve raised your budget to $1,000, I’d consider adding the Icom IC-7300 to your list. At present, via Universal Radio you can buy a new IC-7300 for a net price of $1039.95 after rebates. Sometimes, the price will go even lower although during the C-19 pandemic, I think that’s less likely to happen since supplies are lower than normal for many items.

The IC-7300 has better performance specs than the G90 and can output a full 100 watts if you like. The display is touch sensitive rather than capacitive like the GSOC. The display is also much smaller than that of the GSOC. The IC-7300 has a lower noise floor than the G90.

I think the IC-7300 is a great radio for SWLing, but the audio for broadcasts is sort of “flat.” You might check out this post where we did some audio comparisons. It does have native broadcast recording to an SD card, which I love. The GSOC should be adding this soon, too.

I would include the new Icom IC-705 as a recommendation here, too, but it’s $300 over your budget.

A PC-connected SDR and separate transceiver

This might be the option I’d take if I were in your shoes.

Get the 20 watt Xiegu G90 ($450) as planned or consider a radio like the 100 watt Yaesu FT-891 ($640), Both of these radios are general coverage and would serve you well for SWLing and ham radio activities. I’d personally invest the bit extra and get the FT-891 since it would also give you 100 watts output and even has advanced features like memory keying.

We actually mentioned both radios in a similar post this year.

If you buy the pricier Yaesu FT-891, you’d still have $360 to invest in your shack!

I’d then buy an Airspy HF+ Discovery ($170–my review here) or SDRplay RSPdx ($200–my review here) and get all of the benefits of a PC-connected SDR.

These SDRs would take your SWLing to the next level. They have uncompromised performance for the price.

Both companies continuously improve their products/applications based on customer feedback. Indeed, check out some of our recent posts about SDR# free upgrades. Mind blowing stuff–!!!

You could even use the SDR as a panadapter for your transceiver which would give you the ability to have a full-screen spectrum display on an external monitor at home.

More options?

Of course, these answers only scratch the surface. I haven’t even included used, late model gear in these recommendations.

I’d like to give you a firm recommendation about the GSOC and G90 combo, but I’m waiting to see how this next firmware upgrade goes–early days still.

Post readers: Please comment if you have even more options/suggestions for Tim. What works for you within a $1,000 budget.

Spread the radio love

Which would you choose as a first radio–the Icom IC-7300 or Xiegu G90?

36 Replies

Many thanks to SWLing Post contributor, Paul, who writes:

This came to me from a friend; he is curious about choosing between the Xiegu G90 and the Icom IC-7300 for his first rig. He has money to buy the Icom which is $999 right now after rebates, but wants to know if he is really getting twice the radio for the Icom, vs the Xiegu, or are there other good reasons to get the 2016-introduced Icom, vs the newly introduced Xiegu.

Maybe this can be a posting to ask your readers? Greatly appreciate it.

Thanks very much
Paul

Thank you for passing along the question, Paul.

While I almost consider this to be an “apples to oranges” question, let’s approach this from a couple of different operator perspectives and truly explore the decision.

I like both radios for different reasons, but first, I’ll tell you what my decision would be if I were in in his shoes…

The Icom IC-7300 SDR transceiver

I would choose the Icom IC-7300

While the Icom IC-7300 does cost twice the amount of a Xiegu G90, it’s a much more versatile transceiver. There are almost too many IC-7300 features to list here, so I’ll mention a few that immediately come to mind, focusing on features the G90 lacks.

For one thing, the IC-7300 is a 100 watt radio, thus the max rated power output is five times that of the Xiegu G90.

The IC-7300 doesn’t require an external sound card for digital modes. Simply plug the radio into you PC with a USB cable, and with your favorite application (like WSJT), you can operate any number of digital modes. (I found configuring the G90 for digital modes to be a bit frustrating.)

The IC-7300 also covers the 6 meter band–the G90 tops out at 10 meters.

The IC-7300 has useful features for contests and field operation like:

voice and CW memory keyers with beacon mode,
native transmit and received audio recording,
a large touch screen display to quickly enter frequencies and adjust settings,
audio EQ on both transmit and receive,
a built-in bail
notch filters and Icom’s twin passband tuning

Again, by no means is this a comprehensive list–just some of the features that come to mind.

As a first rig, the IC-7300 can take you into any aspect or mode of the HF band your friend cares to explore. It must be one of the most popular HF radios on the market right now, so there’s also a massive user and knowledge base out there on the web.

The IC-7300 also has better transmitter specs, producing a cleaner signal than the G90, especially in CW (the G90 is known to produce key clicks and not recommended for use with an amplifier). It also can handle close-in signals better than the G90 and has a higher dynamic range. Overall, it has better specs than the G90.

For a more detailed look at the IC-7300, check out my full review.

Why one might choose the Xiegu G90 over the Icom IC-7300

The Xiegu G90 with upgraded encoder

Let’s get an an obvious point out of the way first: the G90 costs half that ($450) of the IC-7300 (generally $900-1,100). This could leave your friend with even more money to invest in an antenna. As I’ve said so many times before, a radio is only as good as its antenna!

If your friend plans to operate primarily in the field, the Xiegu G90 is much more portable option. The G90 is very compact and weighs a fraction of the IC-7300. The G90 also draws less current in receive mode, so is much kinder on a battery. It also has built-in side extensions to protect the front and back panels while being transported.

The Xiegu G90 has a detachable face plate which would come in handy for mobile installations (although, admittedly, there are a number of better mobile transceivers on the market).

My full review of the Xiegu G90 is in this month’s issue (Aug 2020) of The Spectrum Monitor magazine. It’s nearly a 4,000 word review so is one of the longer ones I’ve produced. If your friend wants to make a decision soon, he/she might purchase this issue to fully explore this rig.

Another option: Yaesu FT-891 and LDG Z-11 Pro 2 external antenna tuner combo

If your friend is seriously considering the Xiegu G90, then I have to assume he/she has portable operation in mind.

Making this assumption, I would also suggest they check out the Yaesu FT-891. Like the IC-7300, it has a full 100 watts output and also covers the 6 meter band. Like the G90, the front panel can be separated from the radio body for easy mobile installation.

Although I have never reviewed the FT-891 (although I plan to before the end of the year), the radio has an almost cult-like following among SWLing Post readers. It’s also a favorite rig of Parks On The Air (POTA) activators because of its 100W output, relatively compact footprint, and great audio characteristics. The G90 and IC-7300 both are based on SDR architecture, the FT-891 is a triple conversion superheterodyne general coverage receiver.

Unlike the IC-7300 and G90, however, the FT-891 lacks an internal antenna tuner (ATU) and I’m guessing your friend wants one based on the fact both the G90 and IC-7300 have one.

The LDG Z-11 Pro 2 ATU

No problem! The Yaesu FT-891 is one of the best bang-for-buck transceivers on the market. The price at time of posting is $609 after rebates. That leaves room to purchase a benchmark portable HF+6 meter antenna tuner. I personally love the LDG Z-11 Pro 2 which would only set them back $169. I’ve owned one of the predecessors of this ATU for nearly a decade. It’s located outdoors, in an enclosure and serves as a remote antenna tuner for my multi-band sky loop. It has operated flawlessly through seasonal temperature extremes and powered by a 15 year old 12V gel cell battery that is charged off of a 5 watt PV panel and Micro M+ charge controller.

The FT-891 and Z11 Pro 2 ATU combo would total $778 which is a nice compromise between the $1,000 IC-7300 and $450 G90.

If your friend wanted a more compact option than the IC-7300, and better specs and more power output than the G90, this FT-891/Z-11 Pro 2 combo would be hard to beat.

Don’t Forget Antennas and Power

As I mentioned before, do your friend a favor and remind him/her to set aside a budget for an antenna.

If you build your own wire antenna, you can create an amazing one for $50 or so in quality ladder line and wire–at least, that’s about what I put into my sky loop antenna. Retailers like Universal Radio, HRO, and Gigaparts stock quality pre-made wire antennas that cost a bit more, but are pre-tuned, durable and very easy to deploy. The type of antenna you can install is totally dependent on the environment around your home, access to your radio room, and any local interference you might need to mitigate.

Of course, all of the radios mentioned above need a DC power supply. There are many on the market from lightweight switching power supplies to heavy linear supplies.

I would not choose one of the cheapest ones you can find because switching power supplies especially can inject noise. I’m a big fan of the Powerwerx SS-30DV which will typically cost around $110 at ham radio retailers (although, at present, it’s one of the many items out-of-stock due to the Covid-19 pandemic). It hits the sweet spot for me and is a little workhorse!

What do you think?

As I always say: radios are a personal choice. Specifications and features make for convenient points of comparison, but often choices are made based on a user’s own needs and operating style.

Between the Xiegu G90 and Icom IC-7300, which would you choose as a first rig? Can you think of a better compromise? Please comment!

Do you enjoy the SWLing Post?

Please consider supporting us via Patreon or our Coffee Fund!

Your support makes articles like this one possible. Thank you!

Spread the radio love

Radio Deal: HRO Black Friday sale Yaesu FT-891 $589.95

1 Reply

Many thanks to SWLing Post contributor, Robert Gulley (K4PKM), who notes that HRO’s Black Friday sale also features one of his favorite full-featured mobile HF rigs: the Yaesu FT-891 for $589.95.

Click here to view this deal at Ham Radio Outlet.

Check out all of our holiday sales tips by bookmarking the tag Black Friday Radios 2019.

Do you have a deal tip? Please share them via email, or simply leave a comment!

Spread the radio love