The Tecsun PL-880: triple conversion architecture

Many thanks to SWLing Post contributor, Larry Thompson, who writes:

There’s been some confusion on my part whether the Tecsun PL-880 is a dual conversion or triple conversion receiver. Amazon and eBay list the receiver as double conversion, whereas Universal Radio doesn’t mention either.

After scouring the Instruction Manual, I was pleased to learn that the PL-880 uses the Silicon Labs si4735 DSP microchip and has 4 Intermediate Frequencies.

1st IF: 55.845 MHz
2nd IF: 10.7 MHz
3rd IF: 45 kHz
4th IF: 128 kHz (exclusively for FM)

To me, that looks like a triple conversion architecture. The combination of the DSP microchip, and the triple conversion would explain why my Tecsun PL-880 is so much more sensitive and selective than my Sony ICF-SW8600GR.

My CountyCom GP-5/SSB emergency portable also has the same Silicon Labs DSP chip and it is almost as sensitive as the Tecsun PL-880, far more sensitive than the Sony. I’ve owned a Japan Radio JRC-525 and a Yaesu FT-900AT transceiver for many years, and the PL-880 digs out weak signals better than both those tabletop receivers, both dual conversion.

To quell the speculation, yesterday I contacted Anna at Anon-Co, the worldwide distributor for Tecsun radios. Her quick reply confirms my suspicions that the Tecsun PL-880 is indeed a triple conversion receiver. That would explain why it blows my Sony ICF-SW7600GR out of the water in senitivity and its ability to pull out weak stations.

Among all the other great attributes, this is an welcome discovery and one never mentioned in the specs by the various retailers of this receiver!

Thank you Larry, for shedding light on this–Anna would certainly know.

Your note makes me realize that I really should order a second, current production model PL-880. My PL-880 is from one of the first batches produced. I imagine I could benefit from some of the firmware tweaks that have been made to this receiver over time. Perhaps it would even be a good time to compare the 1st generation with the current generation?

I just checked and Anon-Co is selling the PL-880 on eBay for $153.99 US shipped.

Have any SWing Post readers compared early and late model PL-880 units? Please comment.

Ian’s 80th birthday celebration

2 Replies

Ian McFarland (Photo: Colin Newell at DXer.ca)

Earlier this month, Colin Newell asked SWLing Post readers for birthday wishes and memories to share with former Radio Canada International host, Ian McFarland.

Yesterday, I received the following message from Colin:

“For a guy who just turned 80, Ian McFarland looks and sounds amazing.

For the 50+ folks that sent their best wishes for this veteran of World Band Radio, thank you, thank you and thank you.”

Colin has posted photos over at DXer.ca.

You’re right, Colin…Ian looks great! Thanks everyone!

Shortwave List: Cap’s shortwave schedule Android app now open to Beta testing

19 Replies

A few months ago, long-time SWLing Post contributor, Cap Tux, designed a simple shortwave schedule application for his Android phone. Though he never intended to make the app public, he shared it with me to test on my Moto G5 Plus.

Cap has recently decided that if others in the SWLing Post community would like to Beta test his app, they’re welcome to do so. He notes:

The app was created initially to meet my own requirements as at the time I was travelling a lot for my job and other apps I tried didn’t meet the requirements e.g. Broadcast stations only, filter by Station, Freq, Time, Language and more recently ‘Target Area’ which was added to the app very recently as I was initially using the AOKI list but found that EIBI was updated more frequently and tended to be more accurate.

I do miss some of the features and simplicity of the AOKI list as programming some of the code to respond to the amount of info in the EIBI list was challenging and there is still more that can be done. There is a bug on Android v4.4 (not my bug but the frameworks bug) which I have fixed in v1.1.10 which I can send through later.

I wrote this app as I needed a phone app for my portable radios (PL-660/PL-365) so I could search for shortwave stations using any combination of Station, Frequency, Language, Time (Specific, Real-time incl. day or Any!) or Target Area. The search can even take account of the day of broadcast so if it’s a Friday and the broadcast is only a Saturday, then it won’t show it.

Shortwave List Features:

Search the list using any combination of Station, Frequency, Time, Language, Time or Target Area

Only broadcast stations are included in the list

Scrollable list of stations based on search criteria

Get Station, Frequency, Times, Language, Target, Days on-air, Transmitter location and the Broadcasters country of origin of the selected broadcast by a tap on a station

Powerful search features with a simple interface

Search for specific broadcast times with any combination of Station, Frequency or Language, Target area with future or past times being searchable, although this lists all stations irrespective of the day (as you may want to know a time for a broadcast tomorrow, or yesterday)

Search for stations in real-time with any combination of Station, Frequency, Language or Target Area, so the app only lists broadcast stations on-air now (also takes the day into account, so, for example, a station listed as only on-air on a Friday will not show if today is a Saturday)

Search for stations transmitting at any time with any combination of Station, Frequency Language or Target Area

Future features in active development:

Update shortwave list from the internet

A few examples of use:

You hear a station in an unknown language, Select ‘ON AIR’ and enter the ‘Freq’, ‘SEARCH’ and the app will list the possible stations

You hear a station in English, select ‘ON AIR’ the ‘Language ‘ set to ‘English’ and enter the ‘Freq’, ‘SEARCH’ and the app will list the possible stations on that frequency right now

Want to know when a station is transmitting at a specific time? select the specific time by selecting the UTC time, set the Hour/Minute and enter the station name in the ‘Station’ box and ‘SEARCH’

You are listening to a SDR recording from last week and trying to identify a station, enter the ‘Freq’ and the specific UTC time (or ‘Language’ if known), ‘SEARCH’ and the app will list the possible stations

Want to tune into broadcasts right now in your language? no problem, just select ‘ON-AIR’ and select your ‘Language’ and ‘SEARCH’

List all broadcasts from a specific station, just enter the ‘Station’ name and click ‘SEARCH’

List all broadcasts on right now by selecting ‘ON-AIR’ and ‘SEARCH’

Phones that have been tested and will work (You will need Android v5.0.1 or above):

Samsung Galaxy S4/S7 (I think all the S series from S4 above should be fine as all have a good screen resolution)

Samsung Galaxy J3

Google Nexus 4

Moto G5 Plus

It should be noted that due to the number of low resolution display phones out there some will not be able to operate the app correctly at present due to the current layout of the components and recommend you use a phone with a decent screen resolution around 1080×1920. I plan to address the screen res issue soon.

What I need from Beta-testers who want to file bug reports:
Phone Make/Model:
Android version:
Shortwave List version in use:
Ease of use:
Speed/Performance:
What would you change/remove/add:
Any screen issues, layout problems or difficulty using a feature:

Please submit your feedback on my Twitter account: @swbcdx

Thank you, Cap!

Readers, please keep in mind that this application is not in the Google Play store because it’s in Beta. You’ll need to download the application to your phone, temporarily allow “Unknown Sources” (here’s a short tutorial), then install the app. It’s very important to only temporarily allow “Unknown Sources”–once this app is installed, please reinstate this security measure.

Please note: If you’re not comfortable downloading and installing an app that is not in the Google Play store, please simply wait for this app to hit the Google Play market possibly at some point in the future.

Click the following link to download the application file to install:

http://www.filedropper.com/shortwavelist-v119-no-permissions

This app requires no permissions. The trade-off is that updates to the schedules cannot be initiated without re-installing an updated app with new schedules embedded.

For what it’s worth, I really like this app! Very simple, effective and works offline.

Here are a few screenshots–I love how he’s kept the interface clean and simple:

Thanks again, Cap, for opening Beta testing to our community.

Please submit your feedback on Cap’s Twitter account: @swbcdx

Elad FDM-DUO: now available in camouflage!

2 Replies

The Elad FDM-DUO (Photo: Dennis Walter)

Many thanks to Dennis Walter who shares the photo above from the 2017 Ham Radio Friedrichshafen convention.

I’ve always thought the FDM-DUO was a cool transceiver, but I must admit it looks even better in camouflage.

I did warn our buddy Clint (Oxford Shortwave) that he should stick with his stock black FDM-DUO. You see, he takes his FDM-DUO to the field…literally. Can you imagine how he’d feel losing his top-notch camouflaged DX rig in the rough? 🙂

Valentino experiments with a ferrite sheet loop antenna

3 Replies

Valentino’s homebrew ferrite sheet antenna.

Many thanks to SWLing Post conttributor, Valentino Barbi (I4BBO) who writes detailing a novel approach to FSL antenna design.

Please note that I translated Valentino’s message from Italian to English via Google translate so please forgive any errors. Valentino writes:

FSL antenna radio enthusiasts typically use numerous ferrite bars with high cost, weight and scarcity,

Ukrainian ferrite bar producers have now finished stocks and have raised their prices.

Normally you use this site to build FSL antennas:
http://www.am-dx.com/antennas/FSL%20Antenna%20Design%20Optimization.htm.

I’ve been experimenting with a new antenna design for about 10 days comparing it with a classic FSL with 20 ferrite bars.

Listening to the audio signals are the same, only instrumentally the antenna FSL in ferrite film
Loses -2dB.

The construction is very simple in that the two ends overlap 5 mm.

I did this:

I took a sheet of A4 paper, I cut 5mm paper at one end.

I laid this sheet on a 10 cm (10 cm) diameter PVC tube.

The uncovered part of the tube is cut, now we will have exactly the exact diameter to fix the A4 sheet of ferrite with the overlap of 5 mm.

As for where to source a ferrite sheet, after much research I discovered this supplier almost by accident:

Click here to view the product page and ordering information.

In summary, the main advantages of this antenna design is weight, cost and availability of A4 sheet of ferrite.

Click here to follow Valentino’s antenna project on his website.

Fascinating, Valentino! Please feel free to share any further information about this FSL antenna as you experiment. It’s true that ferrite bars are becoming difficult to source. Sounds like this is an affordable alternative antenna design for ultralight DXing.

BBC News and CBS News enter editorial and newsgathering relationship

5 Replies

(Source: BBC Media Center via Larry W)

BBC News and CBS News announced today a new editorial and newsgathering relationship that will significantly enhance the global reporting capabilities of both organisations. The announcement was made by BBC Director of News and Current Affairs James Harding and CBS News President David Rhodes.

This new deal allows both organisations to share video, editorial content, and additional newsgathering resources in New York, London, Washington and around the world. The relationship between BBC News and CBS News will also allow for efficient planning of newsgathering resources to increase the content of each broadcaster’s coverage of world events.

James Harding, BBC Director of News and Current Affairs, says: “There’s never been a more important time for smart, courageous coverage of what’s happening in the world.

“This new partnership between the BBC and CBS News is designed to bring our audiences – wherever you live, whatever your point of view – news that is reliable, original and illuminating. Our ambition is to deliver the best in international reporting on television. We’re really looking forward to working together.”

David Rhodes, CBS News President, says: “CBS News is completely committed to original reporting around the world – a commitment clearly shared by the BBC.

“There’s no better partner to strengthen and extend our global coverage than BBC News. I look forward to working with James Harding as we increase the capabilities of both organisations.”

Sharing of content between BBC News and CBS News will begin immediately. Additional newsgathering components will be rolled out in the coming months.

The partnership builds on a relationship that dates back to the early days of television and radio news. Legendary journalist Edward R. Murrow delivered many of his famed reports from Studio B4 at BBC’s London headquarters. Murrow discussed his fondness for his work at the BBC’s studio B4, including a microphone he kept in New York with the BBC logo he used covering World War II.

This new partnership replaces the BBC’s current arrangement with ABC News.

James Harding says: “Our relationship with ABC has been long and fruitful. We have worked side by side on some of the most significant stories of our time on both sides of the Atlantic, from the attack on the Twin Towers to the wedding of the Duke and Duchess of Cambridge. We wish ABC well and would like to thank them for many years of hard work and expertise.”

Follow Dave Zantow for Icom IC-R8600 updates and evaluation

1 Reply

Many thanks to SWLing Post contributor, Dave Zantow (N9EWO), who writes

Have a few IC-R8600 “first observations” posted on the test sample we now have here.

It looks much better in person than in the photos (very nice).

It is also a bit smaller than the IC-7300.

http://webpages.charter.net/n9ewo2/news.html

Thanks, Dave!

I’ll follow Dave’s updates for sure as he’s a thorough and top-notch reviewer.

To give you an idea of what Dave’s evaluated so far, check out some of his initial impressions:

A few “first” IC-R8600 observations (latest 1.10 firmware) :

General size is slightly smaller than the IC-7300 SDR HF Transceiver.

With the IC-R8600 having a near 2 AMP current draw, does make for very warm operation after a few hours on (that is over double current requirement of what the IC-7300 uses in receive.) It does NOT make use of any cooling fans…whew good news here ! The receiver requires an external power supply, and I REQUIRE my regulated linear power supplies NOT to run HOT with any continuous operation (I would never use a noisy switching supply with it , but that’s my choice). I say the minimum size to use is the Astron RS-12A. While this may seem overkill, we tried a smaller RS-7A and after being on for 2 hours it’s lone pass transistor was too hot to touch which is totally unacceptable to N9EWO’s standards. The RS-12A has 2 pass transistors and a larger heatsink (and thankfully still no fan to create room noise). We have NOT tested a RS-12A with the IC-R8600 to verify this, but should be the one to try (I say don’t go with a lower current model) ???

S-AM modes (AM Synchronous Detector) sadly works the same as in the IC-R9500. In other words, it does NOT help with AM mode fading distortion (adjacent interference help only). So another Icom receiver with very poor “Sync” performance. We can HOPE for improvement on this with later firmware update, but I would not hold my breath ?? Yeah, one can use manual ECSS (zero beat in SSB modes) which does excellent, but SSB modes have limited top bandwidth of 3.6 KHz as all Icom’s do.

It’s top mounted Internal speaker is surprisingly good for it’s size. Tone control has much larger “Bass” range over the IC-7300 (excellent). Super clean audio as with the IC-7300. Connected to a classic Realistic “Minimius 77” 2 way speaker sounds stunning.

Tuning knob is of a “clicky” type (detents) out of the box. Good news , there is to way select a “smooth” feeling knob by moving the 3 position slider adjustment on the bottom of the knob (it’s not so easy to do however). So it goes from left to right : smooth loose – smooth tight – clicky. It has some rotational play in the “clicky” mode (but so does the IC-R9500’s knob in “clicky ” mode), but overall it feels good and this knob scheme was well done.

FMBC reception has a strange ACG pumping trait. Of course on the FMW mode the AGC and decay rate are not adjustable.

Uses no (or fewer) relays with it’s front end filters at least on SW. The “click and clack” when tuning around with the IC-7300 in the SWBC bands does not exist with the IC-R8600 (uses didoes ??). When we can locate a schematic will tell the whole story here (NOTE : No schematics are included with the set).

I’m really curious to see how the IC-R8600 stacks up to the IC-7300 on the HF bands. Looking forward to your updates, Dave!

Check Dave’s radio page regularly for updates.