The Reciva Internet radio station aggregator is closing down

332 Replies

UPDATE: Click here to read about a procedure to extend the life of your Reciva WiFi radio presets before Reciva closes on April 30, 2021.

Many thanks to SWLing Post contributor, John Drake, who notes that Reciva has announced that they are closing down effective January 31, 2021.

Check out the banner on their website:This, of course, is not good news for anyone using a Reciva-based WiFi radio.

Indeed, the WiFi radio landscape has become quite unstable in the past couple of years. Only recently Frontier Silicon/vTuner experienced issues with their database (that was eventually sorted out). WiFi radio manufacturers Pure and Tivoli have been sold to investment firms and users have been displeased with both customer service and issues with their aggregators. TuneIn has also been forced to limit choices for UK users–a decision likely to affect other aggregators. And now Reciva, which was once one of the most popular aggregators on the market, is going to be “withdrawn.”

These are dark days for those who appreciate a dedicated WiFi radio.

Spread the radio love

Steve builds a simple SWL antenna tuner that pairs brilliantly with the Belka-DX

9 Replies

Many thanks to SWLing Post contributor, Steve Allen (KZ4TN), who shares the following guest post:

A Simple Antenna Tuner for SWL Radios

by Steve Allen, KZ4TN

After reading 13DKA’s excellent review of the Belka-DSP on SWLing.com a few weeks ago I knew I had to have one! The size, features, and performance of the Belka-DX (latest version of the Belka-DSP) is phenomenal. I won’t go into reviewing the radio as I couldn’t come close to 13DKA extensive review. If you are considering this SWL receiver his review is a must read.

I love bedtime SWLing and have been putting off setting up an outside antenna specifically to feed into the bedroom for too long. Given that the resonant frequency of the antenna would not be broad enough for the tuning range of the Belka-DX I decided to build a small antenna tuner just for SWLing.

After a couple of hours searching the internet for a simple tuner I found just what I was looking for on http://www.hard-core-dx.com/nordicdx/antenna/lab/tuner.html. It’s a simple L match using a single variable capacitor and coil.

For the coil I wound ~100 turns of 26 Ga wire on a one inch diameter wooden dowel. The wire size can be whatever you have on hand. I twisted a tap every 10 turns. I drilled a hole in each end and glued in a machine screw to mount the coil to the bottom of the enclosure. I’ve had this enclosure in my junk box for a long time and have been waiting for just the right project. The variable capacitor I used was one I found on EBay a few years ago that had two sections, 330 pF and 120 pF. I tied them together for 450 pF. For the rotary switch I had to scratch around on eBay for a while until I found a 12 position single pole.

The plans for the tuner suggested adding a fixed value capacitor with a toggle switch to increase the lower end of the tuning range. I found a 510 pF silver mica and wired it into the circuit.

The antenna I put up is a sloper about 30 feet long.The high end is up about 40 feet and the low end is at about 12 feet. I put the antenna and tuner to the test last evening and the reception on the Belka-DX was superb. With the tuner the strength of the signal would peak about 2-3 units when I found the sweet spot.

The tuner also does double duty as an attenuator for very strong signals.

One mod I made to the Belka-DX was the addition of some grip tape to the tuning knob. It makes fine tuning much easier.

I believe we will continue to see a number of innovative receivers coming to market in the near term utilizing SDR technology. The ratio of performance to size of the Belka-DX is truly amazing in my opinion.

Thank you, Steve, for sharing this brilliant weekend project! As always, brilliant craftsmanship!

Click here to read Steve’s other posts and projects.

Spread the radio love

The new Belka-DX: Georges’ short review and tests

2 Replies

Many thanks to SWLing Post contributor, Georges Ringotte (F6DFZ), who writes:

I received the Belka-DX a few days ago, and it appears to be an outstanding receiver considering its price, its size, and quality of construction.

AGC and audio reproduction are way better than any Chinese SW receiver giving some superb receptions in CW, SSB and AM.

I shall not repeat that other have said, but I must add that the AM2 pseudo synchronous reception seems good to my ears and a bonus with weak signals.

I made some measures :

  • MDS is about -127 dBm in SSB mode, slightly better in CW mode
  • Sensitivity is constant from 1.5 to 30 MHz
  • Image rejection is over 70 dB, better than a KX3 that I tested a few years ago
  • I couldn’t measure selectivity because my HP generator is somewhat noisy, but the Belka-DX is very good, and also way better than Chinese receivers
  • “S meter” is calibrated as follows: -107 dBm = 10 and -37 dBm = 80, and on this range a 10 change equal a 10 dB change, very accurately. Over -37 dBm, S meter doesn’t move any more.
  • Even on my 2x18m center fed or my Hexbeam, I didn’t notice any signs of overload, but as you know the propagation is not outstanding, and BCL stations are not as bothersome as 40 years ago!
  • there are a few birdies, but if you move your frequency 100 Hz away, they disappear

In my opinion, considering the superb quality of reception, this receiver is outstanding.

Best regards.

Georges

Thank you for sharing this, Georges! Sounds like the Belka-DX is a performer!

Spread the radio love

Can you identify this radio in Goldfinger?

9 Replies

Many thanks to SWLing Post contributor, Carlos Latuff, who writes:

As a tribute to Sean Connery, who passed away today, let’s see if your readers may identify this radio set found in Goldfinger from 1964:

Please comment if you can ID this radio in Goldfinger!

Thank you for sharing this, Carlos. Sean Connery was a great man and, no doubt, *the* James Bond for many of us. Rest in Peace Mr. Connery.

Spread the radio love

Ivan demonstrates the incredible SDR# Co-Channel Canceller

1 Reply

Many thanks to SWLing Post contributor, Ivan (NO2CW), who shares the following short demo of the new SDR# Co-Channel interference canceller tool:

That is simply amazing!

Readers note: this powerful tool for DXing is a free upgrade for SDR# users!

Click here to read more about the Co-Channel Canceller.

 

Spread the radio love

The new Yaesu FTDX10: Yaesu’s latest hybrid SDR HF transceiver

35 Replies

I’ll admit it: I like what I see here.

Yaesu has announced their latest compact 160-6 M transceiver: the FTDX10. Based on the specifications, it looks like it borrows heavily from the FTDX101 series, which is a very good thing.

At 5″, the color TFT display is larger than that of the IC-7300 & IC-705. The specifications appear to be benchmark with excellent dynamic range (3rd IMDR quoted at “109 dB or more”).

We’ll post more details as updates become available. Wimo has listed a pre-order price of €1,550.00 w/out shipping or VAT.

Here’s the full press release via WIMO:

We are pleased to introduce the FTDX10, a new long-waiting compact HF/50MHz 100W SDR Transceiver!

– Hybrid SDR Configuration
Like the FTDX101 series, the new FTDX10 utilizes the Yaesu Hybrid SDR configuration – Narrow Band SDR and Direct Sampling SDR. The Narrow band SDR receiver emphasizes excellent receiver performance, while the Direct Sampling SDR provides a Digital Processing Real-Time Spectrum Scope.

– Narrow Band SDR with 3 types of Roofing Filters and Phenomenal Multi-signal receiving Characteristics
Like the FTDX101 series, the Down Conversion type receiver configuration with the first IF at 9MHz has been adopted. It makes it possible to incorporate excellent narrow bandwidth crystal roofing filters that have the desired sharp “cliff edge” shape factor. Thanks to the Narrow Band SDR with the latest circuit configuration including 500Hz, 3kHz and 12kHz roofing filters and lownoise oscillator, the RMDR (Reciprocal Mixing Dynamic Range) reaches 116dB or more, the close-in BDR (Blocking Dynamic Range) reaches 141dB or more, and 3rd IMDR (third-order Intermodulation Dynamic Range) reaches 109dB or more, in the
14MHz band at 2kHz separation.

– 250MHz HRDDS (High Resolution Direct Digital Synthesizer) affords Quiet and Clear Reception
The local circuit of the new FTDX10 uses 250MHz HRDDS method same as the FTDX101 series. Thanks to its characteristics that improve the C/N (carrier to noise) ratio and the careful selection of components in the design, the phase noise characteristic of the local signal achieves an excellent value of -145dB or less in 14MHz at 2kHz separation.

– 3DSS (3-Dimensional Spectrum Stream) on the 5-inch Full-Color TFT Display with Touch-Panel Functionality
The 5-inch Full-Color panel shows the 3DSS display. By touching the frequency display, the numeric keypad is displayed, and the active band and frequency adjustment can be set by direct input. Frequency setting and adjustment can also be performed by turning the MAIN dial or touching the scope display. Similar to the FTDX101 series, the MULTI display, RX operation status display, Center, FIX and Cursor modes are available at WiMo.

– Front Panel Designed for Superior Operating Efficiency
MPVD (Multi-Purpose VFO Outer Dial), is a large multi-purpose ring around the outside of the VFO dial that enables control of
Clarifier, C/S (custom selection function) and recall of memory channels.

– Remote Operation with optional LAN unit (SCU-LAN10, see WiMo Website)
Remote operation of the transceiver is possible with the optional SCU-LAN10 and SCU-LAN10 Network Remote Control Software. In addition to controlling the transceiver basic operations, the versatile scope displays enable sophisticated operation such as monitoring the band conditions on a large display at a location away from the ham shack by connection to a home LAN network.

The features of the new FTDX10 include:
– 15 separate band pass filters
– Effective QRM rejection with the IF DSP (IF SHIFT/WIDTH, IF NOTCH DNF, DNR, COUNTOUR)
– High-quality and super stable final amplifier utilizing the new push-pull MOSFET RD70HUP2
– Aluminum Heat Sink with 80mm low-noise axial flow cooling fan
– High Speed Automatic Antenna Tuner with a large capacity 100-channel memory – RF & AF Transmit Monitor
– Microphone Amplifier with Three-stage parametric Equalizer (SSB/ AM mode)
– QMB (Quick Memory Bank)
– Band Stack Function
– Optional speaker – SP-30 designed for the new FTDX10
– Optional roofing filter (300Hz) – XF-130CN available

The new FTDX10 will be available in early December 2020 at WiMo.

Radio Features:

– HF/50MHz band 100W Transceiver
– Hybrid SDR configuration utilizing a Narrow Bandwidth SDR, and a Direct Sampling SDR
– Narrow Band SDR enables Phenomenal Multi-signal Receiving characteristics (2kHz RMDR 116dB+, 2kHz BDR 141dB+, 2kHz 3rd IMDR 109dB+) – Down conversion,
9MHz IF Roofing Filters produce Excellent Shape Factor
– 250 MHz HRDDS (High Resolution Direct Digital Synthesizer) Ultra Low-Noise Local-Oscillator System
– 15 Separate Powerful Band Pass Filters (BPF)
– Effective QRM Rejection with IF DSP (IF SHIFT/WIDTH, IF NOTCH/DNF,CONTOUR,DNR, APF)
– High-quality and Super-Stable Final Amplifier utilizing the new push-pull MOSFET RD70HUP2
– 5-inch Full Color Touch Panel and 3DSS (3-Dimensional Spectrum Stream) Display
– MPVD (Multi-Purpose VFO Outer Dial) enables Outstanding Operating Performance
– Quick Memory Bank (QMB)
– Supports CW operation with multiple functions such as: CW zero-in, CW Auto zero-in, CW Reverse, CW decode, CW keying Signal form Shaping by FPGA and others
– RTTY (FSK)/ PSK Encode/Decode Function
– Other practical features such as Optional RF Gain Selection by IPO. Automatic Gain Control, Quick Split Function – SD Card Slot
– Remote Operation via Internet with optional LAN-Unit (SCU-LAN10 see WiMo website)

Supplied Accessories:

Microphone SSM-75E
DC Power Cable w/Fuse
Spare Fuse
6.3mm 3-contact Plug
Operating Manual

Specifications:

Frequency Ranges:

RX

  • 30kHz – 75MHz (Operating)
  • 1.8MHz – 29.699999MHz (Specified performance, Amateur bands only)*
  • *5.1675/5.332/5.348/5.3585/5.373/5.405MHz (US only), 5.351500-5.366500MHz (EU only)/ 5.25000-5.406500 (UK
    only)
  • 50MHz – 53.999999MHz (Specified performance, Amateur bands only)
  • 70MHz – 70.499999MHz (Specifed performance, UK Amateur bands version only)

TX

  • 1.8 – 54MHz (Amateur bands only)

Modulation Type: A1A(CW), A3E(AM), J3E(LSB,USB), F3E(FM),F1B(RTTY),G1B(PSK)
Frequency Stability: ±0.5ppm (32°F to +122°F/0? to +50?, after 1min)
Supply Voltage: DC 13.8V ±15%
Circuit Type: Double-Conversion Superheterodyne
Intermediate Frequencies 1st IF 9.005MHz; 2nd IF 24kHz
RF Power Output: 5W – 100W (CW, LSB, USB, FM, RTTY, PKT); 5W -25W (AM)
Case Size(W x H x D): 10.47 x 3.58 x 10.35(inch) / 266 x 91 x 263 (mm) *Protruding parts not included at WIMo
Weight (Approx.): 13lbs/ 5.9kg

Spread the radio love

CHA MPAS Lite: A proper quick-deployment field antenna

11 Replies

Chameleon Antenna recently sent me a prototype of their latest antenna: the CHA MPAS Lite.

The MPAS Lite is a compact version of their MPAS 2.0 modular antenna system and designed to be even more portable.

Chameleon Antenna is a specialist antenna manufacturer that makes military-grade, field portable antennas that are low-profile and stealthy. Chameleon products are 100% made in the USA and their customers range from amateur radio operators to the armed forces.

Their antennas are not cheap, but they are a prime example when we talk about “you pay for what you get.” In all of my years of evaluating radio products, I’ve never seen better quality field antennas–they’re absolutely top-shelf.

Zeta

I’m currently in my hometown doing a little caregiving for my parents. I’d only planned to be here for a couple of days, but when I saw that the remnants of Hurricane Zeta would pass directly over us with tropical storm force winds and rain, I stuck around to help the folks out.

Zeta struck quite a blow, in fact. No injuries reported, but over 23,000 of us have been without power for over 34+ hours in Catawba county. With saturated grounds, the winds toppled a lot of trees and damaged power lines.

Yesterday, I wanted to take advantage of the power outage and get on the air. I couldn’t really do a POTA activation because I needed to manage things here at my parents’ house. Plus, why not profit from the grid being down and bathe in a noise-free RF space–?

I decided to set it up in their front yard.

CHA MPAS Lite

I had never deployed the MPAS Lite before, so I did a quick scan through the owner’s manual. Although the MPAS Lite (like the MPAS 2.0) can be configured a number of ways, I deployed it as a simple vertical antenna.

Assembly was simple:

  1. Insert the stainless steel spike in the ground,
  2. Attach the counterpoise wire (I unraveled about 25′) to the spike
  3. Screw on the CHA Micro-Hybrid
  4. Screw the 17′ telescoping whip onto the Hybrid-Micro
  5. Extend the whip antenna fully
  6. Connect the supplied coax (with in-line choke) to the Hybrid-Micro
  7. Connect the antenna to the rig

Although I had the Icom IC-705 packed, I wanted to keep things simple by using the Elecraft KX2 I’d also packed since it has a built-in ATU.

Important: the CHA MPAS Lite requires an ATU to get a good match across the bands.

I wasn’t in the mood to ragchew yesterday, but I thought it might be fun to see how easily I could tune the MPAS Lite from 80 meters up.

I checked the Parks On The Air spots page and saw NK8O activating a park in Minnesota in CW:

He was working a bit of a pile-up, but after three calls, he worked me and reported a 559 signal report. Not bad at 5 watts!

I then moved to 40, 18, and 20 meter and called CQ a couple times to see if the Reverse Beacon Network (RBN) could spot me. I like using the RBN to give me a “quick and dirty” signal report. I was very pleased with the bands I tested:

Those dB numbers are quite good for an op running 5 watts into a vertical compromised antenna.

The KX2 very effortlessly got near 1:1 matches on every band I tested.

Of course, after working a few stations in CW and SSB, I tuned to the broadcast bands and enjoyed a little RFI-free SWLing. Noting 13dka’s recent article, I’m thinking on the coast, the MPAS Lite will make for a superb amateur radio and SWLing antenna.

Durability

Although the remnants of Zeta had effectively passed through the area three hours prior, it was still very blustery outside. I was concerned gusts might even be a little too strong for the 17′ whip, but I was wrong. The whip handled the wind gusts with ease and the spike held it in place with no problem.

One of the things I have to watch with my Wolf River Coils TIA vertical is the fact it’s prone to fall in windy conditions and many ops have noted that this can permanently damage the telescoping whip (the weak point in that system).

I’m pretty certain this wouldn’t happen with the Chameleon 17′ whip–it feels very substantial and solid.

Ready to hit the field with the CHA MPAS Lite!

I’m a huge fan of wire antennas because I believe they give me the most “bang-for-buck” in the field, but they’re not always practical to deploy. I like having a good self-supporting antenna option in my tool belt when there are no trees around or when parks don’t allow me to hang antennas in their trees.

I’ve got a park in mind that will make for a good test of the CHA MPAS Lite: it’s a remote game land with no real parking option. I’ll have to activate it on the roadside–an ideal application for the MPAS Lite.

Click here to check out the CHA MPAS Lite.

Spread the radio love