Patrizio’s simple homebrew NCPL antenna

Leave a reply

Many thanks to SWLing Post contributor, Patrizio Cardelli, who writes:

I’m Patrizio (SWL I – 5184 /AN) from Riva del Garda, Italy.

A few days ago, I built a Noise-Cancelling Passive Loop (NCPL) antenna. I built the 1:1 balun with a couple of ferrite 175 – 285.

I got a good result on medium wave on my ICOM IC R 71 E with the antenna inside my house installed behind the desk just to avoid any problems with my wife.

On shortwave, the signal was low in comparison with the Bonito mini whip but in my QTH I have a lot of QRM and with this antenna I solved my problem.

Yesterday I tried the balun with my random wire (15,2 meter long) also with good results.

About my NCPL antenna: I made mine with RG-58 coaxial cable just to have easy portability in SOTA (please see photo) and also the feed line is made by the same coaxial cable. OK, you are right…it’s ugly:

Electrical connections are not soldered, still I don’t see any mechanical issues and this antenna since it is made for SWL / BCL purposes (meaning, RX only, no TX).

Concerning the binocular ferrite core, I didn’t have one, so I used two ferrite core type 175 – 285 (28,5 mm length, external diameter 17,5 mm and internal diameter 9,5 mm) normally used to reduce HF interference:

For the winding I used PVC insulated cable cat no: 7/0,2 type 2 (def61 – 12) conductor 7/0,2mm TSCu X 0,3mm R/T type single (4 turns primary and 4 turns secondary). It’s the same cable with which I built my random wire antenna (also portable for SOTA but now installed on my balcony until the COVID – 19 emergency is over).

The attached videos show the situation in comparison with my BONITO MINI WHIP active antenna (also installed inside my house). Recently I changed my QTH and unfortunately here I have a lot of interference both on MW and SW. The better results that you can hear are achieved with my NCPL antenna.

I have made this test with my ICOM IC R 71 E + BHI noise cancellation speaker…..you can assess yourself, the better results that you can hear are achieved with the NCPL antenna and in the case of Tecsun PL-660 without any noise cancelling filter (BHI speaker off).

Thanks for sharing this, Patrizio! As you say, the NCPL loop seems to do a fine job helping to eliminate local RFI/QRM. The Bonito Mini Whip is a fine antenna, but not optimal for environments with a lot of radio noise–that’s where the NCPL antenna really shines.

You also make a good point that if you’re simply experimenting and only using an antenna for receiving, you can be more relaxed about the build because you’re not sending RF through it. In the end, however, properly soldered and protected connections will last much longer and provide better, more reliable performance.

Thank you, again, for sharing your build, Patriio! Those reception results speak for themselves!

Spread the radio love

My Replacement Stand Journey for the Grundig G6 Aviator

6 Replies

 

Guest Post by Troy Riedel

I’ve mentioned here in the past that I am an astronomy hobbyist first, and an SWL hobbyist second (call SWL my cloudy nights hobby).

A couple of years ago my Grundig G6 suffered from the troublesome “sticky” body that afflicts all of the Grundig/Eton radios of that era.  I used the recommended cleaning agent as has been posted here (Purple Power) to remove the sticky residue.  It worked great – but I discovered one must be very careful using this cleaner.  Why?  Excess cleaner seeped into the crevices where the radio stand mounts, was not fully removed/dried, and the cleaner “ate” the nubs off that hold the radio stand in place.  The result: a broken radio stand!  Right Photo: you’ll see glue residue smeared on the broken stand – where I tried to make & glue new nubs and failed miserably.

Through my astronomy hobby, I discovered someone (Joel) who 3D prints some astronomical accessories.  After ordering & receiving three quality products, we established a friendly rapport.  I asked him if he knew of anyone who 3D printed and commercially sold radio stands.

He replied “No” – and frankly he wasn’t quite sure what I was referring to – but he essentially conveyed “if you supply me a photo and dimensions, I will gladly print one that you can try”.  Great news!

After supplying him a photo and supplying dimensions, Joel printed off a stand plus a spare and shipped it to me.  Unfortunately, it did not fit … the side nubs were simply too small.

I wrote-off the encounter as having been worth the nominal cost & effort.  But Joel was not ready to write this off!  He asked for more details re: why it didn’t fit (we designed the stand about .25mm too thin – a small tolerance but significant in that the stand simply would not fit – the nubs were too small at the thickness that was printed).  We consulted, both made recommendations, then Joel promptly 3D printed another stand (v.2) and mailed it to me.

The end result: it fits perfectly – works perfectly.  I now have a replacement G6 stand and I feel my little Grundig Aviator Buzz Aldrin Edition (note the astronomy connection) was now, once again, whole!

 

For those who’ve replaced radio stands before, the biggest obstacle is *not* breaking it when you try to insert it into the back of the radio.  A tried and true trick is to freeze the replacement stand, so it contracts very slightly (by the mm), and then insert it into the body of the radio.  The great thing about this stand: it is designed with a cut-out on each side.  This cut-out allows the stand to ever-so-slightly flex (better – and probably more safely – than the freezing trick). This design allowed me to safely and rather effortlessly insert the stand without fear of breaking it.  And the stand’s thickness is quite capable of supporting the weight of the radio (note: the plastic of the 3D printed stand is not quite as hard as the OEM stand but it is still more than capable of supporting the radio’s weight).

I’m sharing this because Joel has added the G6 stand to his little BuckeyeStargazer Web Store , for $10 – what a great deal for us suffering G6 folks with broken stands.

At this time, the Buckeye Stargazer only offers the G6 stand.  But, who knows?  Before I came along, he didn’t offer any stand.  You might be able to cajole Joel into prototyping another stand?  For that – you’d have to contact him directly to see if he were receptive to more experimentation.

So, thanks again to the Buckeye Stargazer!  It’s always nice to tie my two hobbies together: astronomy & shortwave radio.

Spread the radio love

Using Adobe on Android to read The Spectrum Monitor magazine

2 Replies

Many thanks to SWLing Post contributor, Bill Hemphill, who writes:

I was very happy to see your post about The Spectrum Monitor magazine. Like you, I am a big fan of it and have subscribed for several years and have purchased the archived years.

Usually, I am not a fan of digital magazines. They either are in special formats requiring special programs or even special versions of Acrobat. Like you, I was happy to see that it is in standard PDF format.

But that still brought up a problem. With my eyesight, I need to zoom in on the page to read it, even when using a 10” tablet and definitely if using a smaller screen such as my phone. Normally it means panning around the page, reading column one down and then going back to the top of the page to read the second or third column.

But there is some good news that many people may not be aware of. The Acrobat Reader app on the Android system allows for a mode called “Reading Mode”. What reading mode does is stack the columns up into a single column thus allowing for reading straight down – no more scrolling back to the top of the next column. And you can tap on the screen to enlarge the text and the text will reformat in a larger font to fit the margins of the screen.

I took some screen shots of TSM using Adobe Reader on my Android phone.

On the left is the complete page, on the right I have tapped on the page and while it enlarged it, I now need to scroll around to read it:

Following screen shot shows the “View Setting” Settings and “Page-by-Page” is the default setting.

What you want do is change this to “Reading Mode”:

Once you have selected “Reading Mode” you will find that the columns are now stacked vertically and you can read my just scrolling down. No more going back to the top for the next column. Also, taping on the text will enlarge it and reflow it to fit the device screen.

Left screen shot is after selecting “Reading Mode” and right is after tapping the screen to enlarge the text:

With Reading Mode, I find I can even read TSM on my Cell Phone Screen as well as my tablets.

Note: Reading Mode only works with PDF’s that have been created with this is mind. It obviously won’t work with PDF’s created from scans.

Unfortunately, while there is a “Read Mode” in Acrobat Reader DC for Windows, it does not stack the columns like the Android version does. I’m not sure if the Acrobat Reader for iPhone works the same way as Android.

Hope this is of help to others.

73
Bill Hemphill
WD9EQD
Smithville, NJ

Thank you so much, Bill, for sharing your tip! You make a really good point, too, that PDF publications give you the flexibility to change text size and adjust layout through Adobe Reader so that it’s quite easy to read even on a small device. I’m also a huge fan of PDF documents and wish other radio publications would consider adopting the PDF format instead of replying on proprietary readers and apps.

Click here to check out The Spectrum Monitor magazine. 

Spread the radio love

FTIOM & UBMP, May 10-16

Leave a reply

From the Isle of Music, May 10-16:
This week, in the first half we present part two of El Invierno según Virulo, a “songo opera” recorded in 1982. In the second half Osamu Menéndez joins us to present his great new rock cubano album 2020.
1. For Eastern Europe but audible well beyond the target area in most of the Eastern Hemisphere (including parts of East Asia and Oceania) with 100Kw, Sunday 1500-1600 UTC on SpaceLine, 9400 KHz, from Sofia, Bulgaria (1800-1900 MSK)
If you don’t have a shortwave radio or are out of range, you can listen live to an uplink from a listening radio in the Netherlands during the broadcast at
http://websdr.ewi.utwente.nl:8901/?tune=9400am
2. For the Americas and parts of Europe, Tuesday 0000-0100 on WBCQ, 7490 KHz from Monticello, ME, USA (Monday 8-9PM EST in the US).
If you don’t have a shortwave or are out of range, you can listen to a live stream from the WBCQ website here (choose 7490): http://www.wbcq.com/?page_id=7
3 & 4. For Europe and sometimes beyond, Tuesday 1900-2000 UTC and Saturday 1200-1300 UTC on Channel 292, 6070 KHz from Rohrbach, Germany.
If you don’t have a shortwave radio or are out of range, you can listen live to uplinks from various websdrs in Europe.
Visit our Facebook page at https://www.facebook.com/fromtheisleofmusic

Uncle Bill’s Melting Pot, May 10 and 12:
Episode 164 salutes the mothers of the world with music about them from several countries.
The transmissions take place:
1.Sundays 2200-2300 (6:00PM -7:00PM Eastern US) on WBCQ The Planet 7490 KHz from the US to the Americas and parts of Europe
If you don’t have a shortwave or are out of range, you can listen to a live stream from the WBCQ website here (choose 7490): http://www.wbcq.com/?page_id=7
2. Tuesdays 2000-2100 UTC on Channel 292, 6070 KHz from Rohrbach, Germany for Europe.
If you don’t have a shortwave radio or are out of range, you can listen live to an uplink from different web SDRs in Europe
including a live uplink from a listening radio in the Netherlands at http://websdr.ewi.utwente.nl:8901/?tune=6070am
Visit our Facebook Page at https://www.facebook.com/UncleBillsMeltingPot

Spread the radio love

Spectres of Shortwave: Amanda Dawn Christie’s film about RCI Sackville now streaming

11 Replies

IMPORTANT UPDATE – Amanda Dawn Christie notes:

“Unfortunately [this video] was never supposed to be public – it was an accident on my part. The film will be viewable soon though, for seven days. May 26 to June 1. It is being hosted by a gallery in Montreal. That upload was only a test for them, and should never have been public. I was in a hurry, trying to get it uploaded before I packed my hard drives before I moved and I guess I didn’t check all the settings. Sorry about that. I appreciate the enthusiasm though.”

SWLing Post friend and filmmaker, Amanda Dawn Christie, has just uploaded a version of her film Spectres of Shortwave to Vimeo where it can be viewed free of charge:

Click here to watch on Vimeo.

Spread the radio love

Finding local Emergency Alert Stations in the US

4 Replies

Many thanks to SWLing Post contributor, Mario Filippi (N2HUN), who shares the following guest post:

Emergency Alert Stations: A great source of local information

by Mario Filippi

During the pandemic a source of local information for residents in certain areas of the country can be found on Emergency Advisory Radio stations that dot the country and provide 24/7 information pertinent to a community.  Not all communities have these stations, which can be found from 1610 – 1710 kHz and operate at varying power outputs.

Author’s Yaesu FRG-100 tuned to EAS station

For example, a station I regularly hear is WRBX655 about 12 miles away in Franklin Township, NJ operating on 1630 kHz : https://www.franklintwpnj.org/Home/Components/News/News/6384/1130?cftype=News

At the moment it is broadcasting information on COVID-19 from the Center for Disease Control.  Every EAS  station has a call sign and wattage generally is from about 10 – 50 watts. However some stations do not necessarily announce their call signs so you can check theradiosource at: http://www.theradiosource.com/resources/stations-alert.htm

Now some of these stations are part of the HAR (Highway Advisory System) that broadcast on major roadways and usually have prominent road signs announcing where to tune your car’s AM radio for latest traffic conditions.  These stations were also termed TIS (Traveler’s Information Stations) at one time and were the precursors of HAR.  However, over the years the FCC allowed more leeway on what information could be broadcast and as a result these EAS stations appeared in communities and even state parks.

You can look up the locations of these stations to ascertain if one serves your community but the best way is to tune regularly from 1610 – 1710 kHz.  The optimal time to listen is during daylight hours as propagation changes greatly after dark and you’ll hear commercial AM radio stations coming in and overpowering most EAS.  As for range, I’ve heard HAR stations as far away as 40 miles depending on ground wave conditions which can vary greatly. QSB is common. Many of these stations will rebroadcast NWS weather information when no pertinent emergencies exist and that is another way to spot them. Some highway stations I’ve heard will begin each broadcast loop with a tone, they’re all different in their approach.

Attached [at the top of the page] is a picture of the author’s Yaesu FRG-100 tuned to WRBX655 from Franklin Township, New Jersey. For an antenna I’ve used a 31 foot vertical and a loop and success will depend on using an outdoor antenna but when away from the home QTH, I’ve heard many of these stations while traveling on the roadways of America, They’re a good break casual AM radio listening.  Give it a try.

Thank you, Mario! I must admit that when I travel, I often hunt down EAS transmitters via my car’s AM radio. Besides being a good source of local information, I do know some DXers who’ve identified and logged an impressive number of distant stations when conditions were ideal. 

If you live outside the US, do you have similar networks for local information? Please comment!

Spread the radio love

BBC: “How amateur radio is connecting people during lockdown”

Leave a reply

Many thanks to SWLing Post contributors, Kris Partridge and Mark Hirst, who share the following article from the BBC:

Coronavirus: How amateur radio is connecting people during lockdown

By Vanessa Pearce
BBC News

Amateur radio use in the UK has seen a “significant” rise during the coronavirus lockdown as people seek new ways of staying connected. The national body that represents users – the Radio Society of Great Britain (RSGB) – has said many people who formerly enjoyed the hobby are also returning to it.

Mark Rider’s social life before the coronavirus lockdown consisted of the occasional trip to the pub, rehearsing with musician friends and visiting his wife in her care home.

“But when I knew that wasn’t going to happen any time soon I decided to dust off my amateur radio equipment to seek out some other social interaction,” he says.

Mr Rider, a retired engineer from North Warwickshire, said “ragchewing” – or chatting to people on the airwaves – “has become one of the highlights of my day”.

“Because I live on my own, and because of lockdown, I knew I couldn’t do what I used to do, which wasn’t going to be very good for me or my mental health.”

The 67-year-old says keeping in touch with others has been more important since his wife was taken into care after a stroke.

“Just speaking to somebody else in the same situation is very rewarding,” he says.

The RSGB defines amateur radio as a “technical hobby for people who want to learn about, use and experiment with wireless communications”, like Mr Rider, who uses his radio kit to speak to others using designated radio frequencies.

Steve Thomas, RSGB general manager, says the organisation has experienced a threefold increase in the number of people asking to sit licensing exams since social distancing rules came into place. There are currently about 75,000 licensed users in the UK.

“Across the country, clubs and individual radio amateurs are supporting one another by setting up ‘nets’, or online meetings,” Mr Thomas says.[…]

Continue reading the full article at the BBC.

Thank you for sharing this excellent article! A number of readers have been commenting about how much more activity there is on the ham radio bands these days. I concur! With everyone at home, ham radio certainly does provide a way to reach out and be a part of a larger community.

Spread the radio love